0
Step 1 : The Crankshaft Position Is located above the starer...
Step 2 : You have to remove the start which has 2 bolts...
Step 3 : Once you remove the starter remove the "Positive Cable" held on by a "10mm" bolt if I'm correct...
Step 4 : Once you have completely removed the starter remove the A/T brace I think it's 2 or 3 "10mm" bolts holding that on...
Step 5 : Once A/T is removed the Crankshaft Position Sensor should be visible...To easily identify there is a connector hanging out of it...It is located in the center of the block rite below cylinder 2, 4, and 6's exhaust manifold....
Step 6 : There is only 1 bolt keeping the sensor from coming out I believe it is either a "10mm" or "11mm"...once the bolt is out there is nothing keeping the Crankshaft position sensor from coming out except to O-ring...You can use a tire iron which I used but be VERY CAREFUL...Because the actually part that makes the sensor work could break off then you will need to drop the oil pan and push it through....
Hopefully This Helps...
What else can I help you with?
What happens if the crankshaft position sensor goes out in a 2001 Oldsmobile intrigue?
The engine won't start.
On a 2000 Olds Intrigue where is the crankshaft position sensor located?
I have Olds Intrigue 2000 3.5L. Needed to replace faulty crankshaft sensor.3.5L engine has two of them. If engine is hard to start cold or hot and engine light is OK.Very common problem for this engine in Aurora 3.5 and Intrigue 3.5 is crankshaft position sensor. Which is located above and behind starter. Starter must be removed first.------------------------------------------------------------------------------------------------------------AnswerLower right hand side of the engine just above the oil pan. Theres a single bolt that holds it in.
Where is the crankshaft position sensor on a 1995 mitusubishi eclipse?
The 1995 Mitsubishi Eclipse crankshaft position sensor is located on the back of the engine. The crankshaft position sensor will be near the bottom of the engine cover.
Is the crankshaft position sensor and engine speed sensor the same thing on a 2004 Nissan altima?
is the crankshaft position sensor the same and the engine speed sensor
What is the crankshaft sensor on a 1995 Chrysler Concorde?
The crankshaft position sensor measures the rotational position of the crankshaft for the engine computer. That info is required for fuel and ignition timing.The crankshaft position sensor measures the rotational position of the crankshaft for the engine computer. That info is required for fuel and ignition timing.
Where is the crankshaft position sensor on 92 Toyota?
the 92 4afe toyota engine does not have a crankshaft position sensor
Does a 1983 Chevy Celebrity have a crankshaft sensor?
No, the 1983 model does not have a crankshaft position sensor. Only distributorless engine needs a crankshaft position sensor.
Where is the crankshaft position sensor 2004 Chevy Malibu?
The 2004 Chevy Malibu crankshaft position sensor location is dependent upon the type of engine. In most cases the crankshaft position sensor is on the back of the engine.
Where is the crankshaft position sensor for a 94 Ford Explorer?
The crankshaft position sensor is located on the front of the engine. It is just to the left of the crankshaft pulley.
Where is a crankshaft sensor on 88 celebrity?
The location of the crankshaft position sensor depends on which engine the car has. If it is the 2.5L 4 cylinder engine the crankshaft position sensor is behind the ignition module. If it is the 2.8L V6 engine the crankshaft position sensor is on the side of the engine nearest the firewall and just above the pan rail in about the center of the block.
Where is the crankshaft sensor on 99 Intrigue 3.5L?
Someone believes you should, "Take Your coolant tank off and the sensor is located under it. It's fairlly simple to replace once you find it."; You will find a sensor there but not the crankshaft sensor. On a 99 Intrigue with a 3.5L, the crankshaft position sensor is in the engine block just above and behind the starter. get under the car, remove the starter and you should find what you are looking for.
Where is the crankshaft position sensor located on a 92 Buick Regal 3.1 V6?
The crankshaft position sensor, on your 1992 Buick regal 3.1 liter, is located on the back of the engine. The crankshaft position sensor is on the inside of the engine cover.
