0
Have a 1976 Chevy 305 with stock intake and 2bbl carb thinking of changing to and Edelbrock Performer intake and 600 CFM carb?
Upgrading to an Edelbrock Performer intake and a 600 CFM carburetor can significantly enhance the performance of your 1976 Chevy 305 by improving airflow and fuel delivery. This combination typically offers better throttle response and increased horsepower, especially at higher RPMs. However, ensure that your engine is in good condition and consider supporting modifications, such as headers or an exhaust upgrade, to maximize the benefits of these changes. Proper tuning will also be essential to get the most out of your new setup.
What else can I help you with?
Will a edelbrock performer 2101 intake help a stock Chevy 305?
Maybe a little, but not much. If you're removing an iron intake, you'd save some weight.
Can you install carporator type eldbrock for 305 engine 1986 without changing the top part of engine?
Or from autozone you can buy a quadra-jet to standard adapter plate if you don't have that edelbrock or if you have a holleythe intake manifold is hopefully what youre talking about and the answer is noAnsweryes you can. if you have a stock intake manifold, which uses a quadrajet carb, you can use edelbrock part number #2696 which you can buy from summit racing (www.summitracing.com). it allows you to use an edelbrock performer square bore carb on the stock quadrajet manifold. for that motor i recommend the edelbrock #1406 which you can also get from summit.
How well will a edelbrock torker 2 intake manifold and a 650 cfm edelbrock carb work on a Chevy small block 400 in a 4x4?
The torker 2 is a single-plane design, so it won't work as well as a 2-plane such as a Performer or Performer RPM.
How much horsepower would a stock GMC 305 have if you put an edelbrock performer intake edelbrock carb headers and a summit cam with 282 int and 292 exh?
around 220hp i would say
What is the torque spec on an Edelbrock aluminum intake manifold for a 78' ford 400m?
Here is the installation instructions for the Edelbrock Performer aluminum intake manifold for a Ford 351M/400...hope it helps out. http://www.edelbrock.com/automotive_new/misc/tech_center/install/2000/2171.pdf
Can you put a eddlebrock carb on a 85 Monte without changing the intake?
I don't think the bolt pattern is the same but you can buy an adapter that bolts to your intake that will accept the Edelbrock.
What intake manifold should you get for your 92 chev 305 with a holley 600 cfm carb?
A 2-plane manifold such as the Edelbrock Performer or similar would be a good choice.
Hi i own a 83 cutlass supreme with a 305 i recently bought a edelbrock 650 thunderseries carb and a edelbrock performer air gap intake just wondering if they'll be fine with a stock cam?
Im gonna say it will be fine, I have a 84 with a 307, just got a performer 600 carb with the 2711 performer intake! You should be good to go, its when you go higher. Although, they say dont go any higher than a 600 on a stock 350 olds :/
What is the torque specs on an edelbrock aluminum intake manifold for a 69' Chevelle 396?
the edelbrock website should have that info.
What is the torque for an edelbrock carburetor on edelbrock intake?
DEPENDS ON WHAT TYPE OF INTAKE AND CARB. YOU'RE BEST BET IS TO GO TO EDLEBROCK.COM, ENTER THE CARBS MODEL NUMBER, AND GET A SPEC SHEET THAT THEY PROVIDE.
Is the edelbrock torker manifold aluminumor cast iron?
I have never seen a cast iron edelbrock intake so I would think not.
Need to replace carb on 82 el camino what would be a good performance choice dont know if it 2 or 4 barrel. It has a 305 engine.?
I would get an Edelbrock performer 4bbl. intake manifold with a Edelbrock 600 CFM. carb, summit racing has everything you need. --------------------------------------------------------------------------------------------------- Holley 650 double pumper for the win!
