answersLogoWhite

0

Maybe a little, but not much. If you're removing an iron intake, you'd save some weight.

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

Where could one order an Edelbrock Performer Series carburetor?

There are a number of stores and garages that stock the Edelbrock Performer Series carburetor. Sites such as Advance Auto Parts, Edelbrock and Amazon all stock the engine.


How much horsepower would a stock GMC 305 have if you put an edelbrock performer intake edelbrock carb headers and a summit cam with 282 int and 292 exh?

around 220hp i would say


Hi i own a 83 cutlass supreme with a 305 i recently bought a edelbrock 650 thunderseries carb and a edelbrock performer air gap intake just wondering if they'll be fine with a stock cam?

Im gonna say it will be fine, I have a 84 with a 307, just got a performer 600 carb with the 2711 performer intake! You should be good to go, its when you go higher. Although, they say dont go any higher than a 600 on a stock 350 olds :/


Have a 1976 Chevy 305 with stock intake and 2bbl carb thinking of changing to and Edelbrock Performer intake and 600 CFM carb?

Upgrading to an Edelbrock Performer intake and a 600 CFM carburetor can significantly enhance the performance of your 1976 Chevy 305 by improving airflow and fuel delivery. This combination typically offers better throttle response and increased horsepower, especially at higher RPMs. However, ensure that your engine is in good condition and consider supporting modifications, such as headers or an exhaust upgrade, to maximize the benefits of these changes. Proper tuning will also be essential to get the most out of your new setup.


Can you install carporator type eldbrock for 305 engine 1986 without changing the top part of engine?

Or from autozone you can buy a quadra-jet to standard adapter plate if you don't have that edelbrock or if you have a holleythe intake manifold is hopefully what youre talking about and the answer is noAnsweryes you can. if you have a stock intake manifold, which uses a quadrajet carb, you can use edelbrock part number #2696 which you can buy from summit racing (www.summitracing.com). it allows you to use an edelbrock performer square bore carb on the stock quadrajet manifold. for that motor i recommend the edelbrock #1406 which you can also get from summit.


How much horsepower does a stock Chevy 350 with a performer rpm air gap intake and a holly 670 street avenger carb have?

275


How much horse power does a Chevy 350 truck motor plus edelbrock performer manifold and carburetor combo plus msd coil have?

The edelbrock performer 350 crate engine has 310hp/375ft-lbs. So if you have the same cam, compression, etc., it should produce close to that.


Will stock 4 barrel carb fit on a performer eps intake?

no!


Is a edelbrock 750 to big for a 1978 Chevy 400 smallblock?

If it is a stock motor then yes it is. 600 CFM carburetor will be just fine on a stock engine.


What engine is this 14057053 on intake Chevy v8?

part # 14057053 4-Barrel Late Model Not Listed All 305 & 350 Aluminum passenger car camaro and truck 1980 - 1985 This is same as the cast iron version, not bad on stock or near stock engine, Comparable to edelbrock performer 2101 or 3701. Good junkyard find for replacing two barrel or cast iron manifold if you plan on using a quadrajet carb. Has good low end throttle response and midrange is ok, will not fit performer or holley carbs, not for racing, great for 305.


Will a 1980 Chevy 305 stock intake fit on a 1980 Chevy 350 motor?

yes


Can anyone estimate how much horsepower torque these parts on a 350 Chevy can give 1-600cfm holley manual choke vacuum secondaries 2-edelbrock torker 2 intake single plane?

Impossible to estimate without detailed information about compression ratio, cam profile, and cylinder head configuration. In general, adding a single plane intake to a stock engine will significantly reduce low-end torque. The Edelbrock Torker II is the worst single plane intake I have ever had the misfortune of using.