0
1969 dart had 340 now 318 in car used 340 motor mounts when i switched used oil pan that was on 318 the center link is rubbing oil pan what is my problem motor mounts or oil pan?
Wiki User
∙ 15y ago
the motor mounts should be the same, as the 318 is the same block as the 340, the only thing I can think of is the oil pan was different on the 340.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you replace the motor mounts on a 1996 grand am se?
you take the mounts of and put new ones on dah
Is taking off the body mounts a good idea?
definitely not a good idea as they stop vibrations into the cabin and they also stop the metal to metal rubbing which can cause weak points in the body. the vibrations can create undue wear on the internal parts of the cabin such as dashes, glove boxes, instrument clusters the list goes on.
How can you tell if motor mounts are bad?
If you rev your motor and the motor moves excessively one or both of your motor mounts is broken. Visual inspection is the best method for determining the condition of your mounts. Jack up the car and put it on jack stands. Get underneath and look at each of the mounts. The rubber should not be cracked or missing pieces. Push on the motor with your hand and make sure the rubber is not broken and that both sides ( motor and the part of the chasis where it mounts ) are firmly attached.
How much do lcd mounts cost at Wal-Mart?
Lcd mounts are quite cheap at wallmart. Their prices are always going down. As of now, Theese mounts only cost 30$...but if you want to check yourself here's a link http://www.walmart.com/
1972 dodge dart with a 1976 block 360 in it the car originally was a 318 car what you have recently noticed is that the center link is rubbing on the oil pan when the steering is turned to t?
Did you use the 318 oil pan????? If not that's why!!!!!The blocks the same width&height.....I have to disagree. I'm doing a conversion on my 67 gt dart that had a 225 slant in it. I'm putting a 360 in it and found that the main caps are different on a 360 than a 318. You have to find a pass. car 360 pan to make it work.Also make sure the motor mounts have not failed allowing the engine to drop lower.
Can an alternator for a 1999 Chevy Malibu be switched with another year of alternator?
if the amperage is the same and it has the same mounts.
How doi keep your fan from rubbing the shroud on 94 s-10?
You may have broken motor mounts.
Where are the motor mounts on a 1999 Chrysler Sebring convertible?
There are four mounts. Center left, right, front, and rear.
Can a 2006 cobalt radio be switched to a 2007 radio?
No. The wiring was changed for 2007 and the radio dimensions and mounts are different as well.
Rear strut mounts welds are braking on my 99 zx2 ford escort is there anything i can do to fix problem?
replace the mounts
What causes motor to rock even when motor mounts are good?
Most likely the gearbox mounts are failing and need replacing. This can cause this problem even when the engine mounts are fine.
Harmonic balance is rubbing on control arm causing sparks?
Check the motor mounts, frame and steering components to see what is damaged or bent. See if the idler arm is installed properly and is not oriented wrong, and DON'T drive the vehicle until you solve the problem.
What is the distance between Chevy motor mounts From bolt hole center to center?
I recently built a engine test stand for a 402ci Chevy engine. The distance between the motor mounts is 16 1/2 inches center to center. This should be true for small block and big block engines.
Equinox Center console vibrates in acceleration?
tranny mounts are going bad
How many motor mounts on a Chevy Impala and where are they?
4 engine mounts. front right, front center, torch strut that supports the radiador, & transmission mount
How many transmission mounts on a 2000 Oldsmobile alero?
there are 3 transmission mounts on the car. Drivers side front, drivers side rear, and a center mount as well
My 98 camaro is shaking you replaced the plusand wires but the problem contines and the check engine light is on what could be the problem?
bat motor mounts cause the shaking a knock sensor realizing its shaking is the light get new mounts
