0
you may want to make sure you have a DUAL(meaning TWO pieces of wire inside the bulb) filament bulb on the brake lights, if you just replaced the bulb and used a MONO filament bulb it will cause this to happen. If this isn't the case, you may want to take it to a mechanic to make sure the sensor that senses when you are pushing the pedal isn't stuck or out that would also cause the same problem.
What else can I help you with?
What is the name of the small rubber piece that is located under the brake pedal that turns off the tail lights?
The part of the car that turns on the brake lights when you apply pressure to the brake pedal is called the brake switch. Releasing pressure from the pedal causes the brake switch to break its electrical contact, turning off the lights.
Brake lights do not work all the time replaced brake light switch?
If you have the same bulb for brake and signal, brake light power needs to be interrupted by the signal lights, The brake circuit has to go through the signal light switch so the problem could be there.
Brake lights don't work when pressing the brake but turn with lights on my 87 Toyota supra?
May be stop light switch--usually located at the upper end of the brake pedal under dash
Your brake blinker and hazard lights dont work you changed the fuse in the fuse box you changed the brake light bulbs and you changed the the oob switch on the brake pedal what could it be?
Have an electrician check the wiring that goes to the brake lights in the trunk of the car.
Where is the rear brake oil input in a 2006 Yamaha v star?
my brake lights stays on wile driving how can i fix it
Where do you add brake fluid on an 1990 Oldsmobile cutlass supreme?
The master cylinder contains the reservoir for the brake fluid. This is where you would add it on an 1990 Cutlass Supreme.
Where is the brake light switch located on a 1980 Oldsmobile Cutlass Supreme 2Dr?
It's on top of the brake pedal under the dash.
What is it when the brake lights on a 1994 Oldsmobile cutlass supreme don't work?
One of two things. Either the brake light switch behind the brake pedal. Or try wiggling or rotating your turn signal stalk in a circle motion. If the brake lights work when the turn signal stalk is wiggled then you need to replace the turn signal stalk.
What size brake pads for a 90 Oldsmobile Cutlass Supreme?
Just tell the parts store what type of car you have and they will be able to get you the right pads.
How do you change front rotors on 1994 Oldsmobile cutlass supreme?
Pull the tires off and take the brake calipers off and the rotors will pull off.
What are the brake rotor discard specs for a 1988 Oldsmobile cutlass supreme with 4 wheel dics brakes?
The minimum thickness specs are stamped into the rotors.
Where is the back up light switch located for a 1989 Oldsmobile cutlass supreme?
Look above the brake pedal on the rod that holds the pedal. There is a button that engages when you depress the pedal to activate the lights. Your parts store will have a replacement and can show you how it is attached.
Why my brake lights on my cutlass supreme work?
Is that a question? They work because that's the way your terrible car was designed to work? Do you mean HOW do they work?
Where is the brake light switch on an oldsmobile cutlass ciera?
In an Oldsmobile Cutlass Ciera, the brake light switch is typically located above the brake pedal, mounted on the brake pedal assembly. It is activated when the pedal is pressed, completing the circuit for the brake lights. To access it, you may need to remove any covering or panel underneath the dashboard. Always consult the vehicle’s service manual for specific details related to your model year.
My brake lights are not working on my 1996 Oldsmobile cutless supreme What should I look for to find out what's wrong with them?
Look for a blown fuse.
Where is the brake relay on a 1995 Oldsmobile cutlass supreme?
On a 1995 Oldsmobile Cutlass Supreme, the brake relay is typically located in the fuse box under the dashboard on the driver's side. You may need to remove the cover of the fuse box to access the relays. Refer to the owner's manual for a diagram to identify the specific relay for the brakes. If you're having trouble finding it, inspecting the fuse box for a labeled diagram can be helpful.
How do you change the brake pads on a 1990 Oldsmobile cutlass ciera?
FRONT OR REAR ?
