0
What else can I help you with?
How do you fix a car blinker that is not working but the hazards are working fine?
Check/change the fuse associated with the blinkers.
If blinkers don't work yet hazards fuses and bulbs are fine what then is it due to something in the steering column because the indicators on the dash for the left and right turn signal?
The turn signal and the flasher use separate flashers. If the dash indicaters come on, do the lights come on but not flash? If yes, probably the flasher. Should be near the hazard flasher. If you don't see it, turn the hazards on and listen for the flasher to click.
You replaced the flasher relay but the turn signals still don't work at all Hazards work fine Why?
on the Chevy beretta there are 2 flashers one is right next to the steering column to the behind the plastic dash piece,this is your turn signal flasher replace it and your signals should work.
Where is the flasher located on a 1998 Dodge Intrepid?
The flasher module is about 2-3 inches below the headlamp switch. Remove the knee blocker from the instrument panel. Pull out the combination flasher slightly then unplug the flasher from the electrical connector. Remove the combination flasher. Use a Tridon Stant EP 27 Flasher or similar.
Does a Mazda 323 have separate flasher units for hazards and turn signals?
I saw in other places that yes it does have separate flashers.
What would cause blinkers on a 1996 dodge ram to stop working even though the fuses and the hazards work and replaced the flasher fuse to?
I have a 1996 D R and have the same problem. Apparently the flasher switch needs to be replaced.
What would make the blinkers not work but the hazards still do?
chances are your flasher for the blinkers OS bad,the flasher for the hazzards are usually on different circits for emergency situations.
How do you fix a turn signal when the hazards work but blinker doesn't?
there are 2 flasher cans in vehicle.one operates hazards and the other operates the blinkers. change the one that operates the blinkers and your blinkers will work
What if your blinkers and hazards do not work on your 1992 Toyota pickup?
If both blinker and hazards dont work check your flasher switch.
Already replaced Isuzu flasher unit with new one - hazards work but turn signals do not - both sides?
u have two flashers on your car... one for blinkers and one for flashers.
Any suggestions on how to fix your blinkers on a 78 Chevy Malibu The running lights and hazards work but the blinkers don't?
Replace the turn signal flasher relay.
Where is the flasher for the blinkers and hazards on a 1978 Datsun 280Z?
On a 1978 Datsun 280Z, the flasher for the blinkers and hazards is typically located under the dashboard, near the steering column. It is often mounted on or near the fuse box. You may need to remove a panel or look closely to access it, as it can be somewhat hidden. Always ensure the ignition is off before attempting to locate or replace the flasher.
What does it mean when the front and back blinkers and the hazards do not work on a 1992 Toyota Camry automatic 4cyl 2.2?
probably a bad emergency light flasher - NOT a turn signal FLASHER- IF the FUSES are good .
How do you fix blinker on a 92 Chevy caprice already replaced flasher back blinkers wont come on front will but none flash and the hazards wont work either?
Assuming you checked all the bulbs and fuses, it sounds like the signal switch is shot.
How do you fix blinkers and hazards that stop functioning on a 92 Nissan 240SX?
this could be a blown fuse, defective flasher, loose connection, or burned out bulb tk
Why dont your blinkers work in your 1990 jetta you changed the flasher and the fuses are not broken The hazards work but turn signals wont?
The 1990 VW Jetta turn signals will not work when the ground wire is broken or corroded. The turn signals may need the lightbulb's replaced.
How do you fix a car blinker that is not working but the hazards are working fine?
Check/change the fuse associated with the blinkers.
