0
Does the harmonic balancer on a 300zx fit all year models from 90 to 96?
Wiki User
∙ 16y ago
Ask the dealer, I believe so. Its the same motor from 89 to 96 with minor differences.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
On a 1990 Acura Integra RS is the crankshaft pulley bolt reverse thread?
No - The crankshaft bolt will loosen counter-clockwise. Because the crank bolt is so hard to remove it can seem as though it is reversed threaded. The crank turns the opposite direction that is used to tighten the bolt. For the crank bolt Lefty-Loosey (counter clockwise), Righty-Tighty (clockwise) apply here. The crank bolt is tightened to 87 ft/lbs of torque. It took more then 87 ft/lbs of torque to loosen my crank bolt. The manual says to apply a drop of motor oil when reinstalling the bolt. An Harmonic Balancer Pully Holding Tool is used to hold the crank while working with the crank bolt. Holding Tools can be found on the internet for $20 to $73. There are two sizes, 45 mm and 50 mm. For a 1990 model year the size is 50 mm. I made an Harmonic Balancer Pully Holding Tool by tack welding a 2 foot length of 1 1/2 inch by 1/2 inch piece of stock, for a handle, on a 2 inch (50 mm) hex nut. The nut fits into the pully to hold the crank and the socket, used to turn the crank bolt, fits through the nut.
Will a 2000 Camry auto transmission work in a 97 Camry?
Most likely it will NOT work. Even so some parts are the same for both cars. But they are both belong to different year models. Toyota is well known for that.
Why did the Cruise Control stop working while you were driving?
a loose wire will cause that. also lots of other reasons but ford is known for cruise control failures in that year on all models
What years are Chinese New Year and ash Wednesday on the same day?
Chinese new year is every year its just a different animal for each year this year (2013) is the year of the snake
How old is a Kenmore Sewing Machine model 158.904 with a wood sewing machine cabinet?
It is my understanding that this machine, the 158.904 was manufactured in 1987 in Canada
Can a harmonic balancer have the wrong keyway?
A replacement balancer could have a wrong keyway. The vehicle could be a half year, meaning that the balancer is listed for one year newer or older vehicle, or the balancer could have been made wrong.
Is a harmonic balancer the for a Chevy 350 bigger then a 305?
it all depends on what year and apllication my 85 was the same according to napa
Where are the timing marks on the cover of a Chevy 350?
The timing marks should be on the driver's side of the car down by the harmonic balancer on a small plate. theres usually a "pointer" on the drivers side. its attached with two of the front cover bolts. When you look down at your Harmonic balancer there should be something about it that you see that looks kinda like saw teeth with numbers in the gaps. The zero or line whichever year you have should be on the Harmonic balancer.
What is the location of the crankshaft position sensor on a Pontiac Montana?
Pending on the year and engine size, some are located within the area of the harmonic balancer.
Where is the crank position sensor on a Chevy Express van?
Depends what year... 99 its right by harmonic balancer in front of motor. 03 its behind stater...
How do you replace a harmonic balancer Hyundai Sonata 2006?
If your Sonata has less than 100,000 miles, take it to your dealer. Parts and labor are covered under the drive train 10 year warrantee.
What year was the silver anniversary 300ZX built?
1995 was the (25th year) silver anniversary for the 300zx.
Which way do you turn the harmonic balancer bolt?
Clockwise, unless it is one of those other cars that you have to turn it Counter-Clockwise: without knowing the exact year, model, and engine of the vehicle it is impossible to answer this question. A typical American made vehicle would require turning the balancer bolt counterclockwise to remove it.
Where is the crankshaft position sensor on a 1996 Chevy 1500?
I don't think that year has one. But if it does then it will be in the passenger side of the timing cover on the front of the engine right behind the harmonic balancer. 1 bolt holds it in place.
Changing a front oil seal on a 350?
This can be quite a job depending on the year of the vehicle. If it's an older vehicle things are a lot easier. Basically, you have to remove everything from the front of the engine so you can get at the harmonic balancer. If you are real lucky you may get by with just removing all the belts. On some vehicles you can get at the harmonic balancer from underneath the car or truck. One way or the other, you have to be able to get at the harmonic balancer. There is a 5/8" bolt in the middle of the balancer. Remove it and use a harmonic balancer puller to remove the balancer. At this point you can see the seal that the snout of the balancer went through. You need a seal removal tool to get the old seal out. Most rental places will have both the harmonic balancer puller and the seal removal tool if you don't. Get the old seal out. Now, take the new seal out of it's package and use a little motor oil on your finger to lube the rubber on the new seal. Put the new seal in using a hammer to tap it into place. This can be a little easier said than done sometimes. Use care not to damage the new seal. Try to get it lined up evenly and just tap it in a circular pattern to get it started. Once you have the new seal in... take a look at the snout of the harmonic balancer and make sure there is not a groove in it from the old seal. If there is one, head to your local auto parts store and grab a harmonic balancer repair sleeve. If all is well you need to use the balancer tool to put the balancer back on. Most balancer tools double as a remover and installer. Make sure you have the key on the crankshaft snout and the groove in the balancer lined up. Once you have the balancer back in place put the 5/8" bolt and washer back in. Use a torque wrench and tighten it to factory specs. If my memory serves me correctly it's 65 ft. lbs. on a chevy. But don't rely on my memory. Now just put everything back on the engine and you're back on the road. This may be a job for a mechanic if you have never done anything like this before. But, it's an expensive job. It's also a good learning experience to do it yourself and save several hundred bucks. The seal itself should be under $20.00 Take pictures of the front of the engine as you remove things. Better yet, get a buddy to video record as you go. It will be a big help when it comes to putting it back together. Also, label everything you can. It's usually a lot harder putting back together than it was taking apart. I would plan on making a weekend of it. Good luck, Guy
In what year did Harmonic Inc - HLIT - have its IPO?
Harmonic Inc. (HLIT) had its IPO in 1995.
Where is the 2 deg.BTDC timing mark and what does it look like?
Modern engines with EFI don't have timing marks on the harmonic balancer. Timing is controlled by the ECU and not adjustable. On older cars, yes, we need what engine
