0
Clockwise, unless it is one of those other cars that you have to turn it Counter-Clockwise: without knowing the exact year, model, and engine of the vehicle it is impossible to answer this question.
A typical American made vehicle would require turning the balancer bolt counterclockwise to remove it.
What else can I help you with?
Which way do you turn the harmonic balance bolt on a 95 Geo Tracker to loosen it?
which way do you turn the harmonic balancer bolt on a 95 geo tracker to loosen it
What way does the harmonic balancer bolt turn on a 61 ford 170ci 6cyl to remove?
Counterclockwise
What way do you turn the harmonic balancer bolt on a 2000 dodge neon?
Clockwise to tighten, counter to loosen.
What way does the harmonic balancer bolt turn on a 96 ford contour?
Counter clockwise. To the left. Lefty loosy.
94 dodge caravan how do you remove the harmonic balancer which way do you turn the bolt to loosen?
lefty loosey righty tighty:)
Which way to turn the bolt holding the harmonic balancer?
To loosen the bolt holding the harmonic balancer, you should turn it counterclockwise. If you're tightening it, turn it clockwise. It's important to check the specific torque specifications for your vehicle, as they can vary. Always ensure you have the correct tools and follow safety precautions when working on your engine.
How do you remove a harmonic balancer on a 2002 Buick rendezvous that has a striped head which way does it go left or right?
To remove the harmonic balancer on a 2002 Buick Rendezvous, first, ensure you have the proper tools, including a harmonic balancer puller. If the bolt head is stripped, you may need to use a bolt extractor or try to grip it with locking pliers. Typically, the harmonic balancer bolt is tightened to the right (clockwise), so you'll need to turn it left (counterclockwise) to remove it. Always refer to a service manual for specific instructions and torque specifications.
How do you remove the harmonic balancer in a 1995 Nissan Maxima GLE?
Start by removing the right front tire and support the vehicle with a jack stand. Then remove lower portion of the splash guard near the harmonic balancer. Remove all drive belts. First remove the A/C alternator belt. Loosen the 14mm bolt at the front of the belt tensioner and then loosen the tensioner bolt (it is the one that's sticking straight up, you use a 14mm socket on it.). The power steering adjuster bolt will be accessed from the bottom near the power steering pump. It has a 12mm bolt head on it. You will break the jamb bolt loose first and then loosen the adjusting bolt. Remove belts. Then remove harmonic balancer bolt (19mm). If the harmonic balancer will not slide off the crankshaft then use a two finger gear puller. Place the harmonic balancer bolt back in the crankshaft but do not tighten it. Leave it about a half inch from being all the way in. Next place the puller on to the harmonic balancer. (one finger on each side securely press into the belt groove.) The center puller bolt will rest against the harmonic balancer bolt head. Tighten the puller bolt and make sure the harmonice balancer bolt does not turn. The balancer should come off at this point.
Is the thread reversed on a Chevy Malibu 2001 harmonic balancer?
Yes, the bolt that holds the harmonic balancer in place on a 2001 Chevy Malibu is reverse thread. I learned that the hard way and stripped the head of my bolt down to nothing. And the bolt is almost impossible to find, because they no longer make them.
How do you install a harmonic balancer on a 1999 Chevy Silverado with a 5.3?
The engine has a harmonic balancer on it, but if it is off, it is easy to re-install. Simply line up the key and tap it on most of the way and torque down the center bolt.
How do you change a harmonic balancer on a 1999 Jeep Cherokee 4.0 L?
Remove the belt. Remove the bolt that attaches the harmonic balancer. Rent or purchase a harmonic balancer puller. Follow the Instructions with the puller and remove the old balancer. Install the new balancer making sure to line up the keyway, a little oil helps. Put the retaining bolt back in and tighten to manufacture specs.
How does the harmonic balancer tighten on a 1989 jeep Cherokee Laredo without turning the crank over?
Easiest way is with an air impact. There are strap clamps available that would go around the harmonic balancer that would hold it while the bolt was tightened.
