answersLogoWhite

0

Start by removing the right front tire and support the vehicle with a jack stand. Then remove lower portion of the splash guard near the harmonic balancer. Remove all drive belts. First remove the A/C alternator belt. Loosen the 14mm bolt at the front of the belt tensioner and then loosen the tensioner bolt (it is the one that's sticking straight up, you use a 14mm socket on it.). The Power Steering adjuster bolt will be accessed from the bottom near the power steering pump. It has a 12mm bolt head on it. You will break the jamb bolt loose first and then loosen the adjusting bolt. Remove belts. Then remove harmonic balancer bolt (19mm). If the harmonic balancer will not slide off the crankshaft then use a two finger gear puller. Place the harmonic balancer bolt back in the crankshaft but do not tighten it. Leave it about a half inch from being all the way in. Next place the puller on to the harmonic balancer. (one finger on each side securely press into the belt groove.) The center puller bolt will rest against the harmonic balancer bolt head. Tighten the puller bolt and make sure the harmonice balancer bolt does not turn. The balancer should come off at this point.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

How do you remove the harmonic balancer in a Nissan Maxima?

To remove the harmonic balancer from a Nissan Maxima, first you need to removed the center bolt. After that, you can use a puller to remove the harmonic balancer. Before you do this, make sure you disconnect the battery and remove the drive belts.


1997 Nissan maxima where does a knock sensor go?

the Knock sensor is located behind the Harmonic balancer pulley. on the bottom sidethe sensor is $95.00 remove the lock down screw unplug and replace


How do you remove the harmonic balancer on a 1990 Nissan 300ZX?

To remove the harmonic balancer on a 1990 Nissan 300ZX, first disconnect the battery and remove any accessories obstructing access, such as the fan and belts. Use a harmonic balancer puller to ensure safe removal by threading it into the balancer and turning the center bolt to pull it off the crankshaft. Be cautious to support the engine if necessary, and ensure all bolts are properly torqued during reinstallation. Finally, check for any damaged seals or components before reassembly.


How do you remove 327 harmonic balancer?

With a balancer puller tool. With a balancer puller tool.


How to remove crank pulley?

On most newer cars, the crank pulley is one piece with the harmonic balancer.... Remove it with a harmonic balancer puller.


Chevrolet harmonic balancer tool?

The harmonic balancer tool is made especially to remove the balancer. Some stores will loan you the tool with a deposit.


How do you remove harmonic balancer on 2000 cougar?

use a harmonic puller


How do you remove a harmonic balancer on a Chevy Malibu with 3.1?

Go to Autozone and tell them u need a harmonic balancer puller


How do you remove the harmonic balancer on a 1998 saturn sl2?

To remove the harmonic balancer on a 1998 Saturn SL2, you will need to use a harmonic balancer puller tool. First, remove any surrounding components that may impede access. Then, attach the puller to the balancer and use a wrench to slowly tighten the puller until the balancer comes off.


How do you remove a harmonic balancer on a 97 Concorde?

Remove upper core support, remove radiator, remove belts, using a hormonic balancer puller(specific for chrysler) remove balancer.


How do you change harmonic balancer on 1991 buick lesabre?

The flywheel has to be held in place by a holding tool, Remove the mounting bolt, then use a balancer remover to pull the harmonic balancer.


What direction to turn harmonic balancer bolt to remove harmonic balancer?

To remove a harmonic balancer, you typically turn the harmonic balancer bolt counterclockwise (to the left). However, some engines may have a reverse thread, so it's always best to check the specific service manual for your vehicle. Ensure that the engine is securely supported and that you have the right tools for the job.