0
By taking the car somewhere to have the problem(s) fixed that are causing the codes.
There are several ways. You can disconnect the battery, wait a little while and then reconnect it; take it to a place that has a code reader (like Autozone); turn the engine on and off several times.
The main point is that if you haven't fixed what caused the light to come on, it will turn on again. If you take it to a place like Autozone, they will tell you what is causing it to turn on.
What else can I help you with?
Where is the ECU located on an 1989 Honda accord?
RH LOWER DASH PANELThe computer or ECU for the 1989 Honda Civic DX is under a metal kick plate under the carpeting on the firewall of the passenger side of the car. If you are looking for the LED to read error codes, there is a hole in the kick plate that will allow you to read the error codes without removing it.http://i205.photobucket.com/albums/bb39/afullaytor89Civickickpanel.jpg http://i205.photobucket.com/albums/bb39/afullaytor89CivicComputer.jpg
What does error code P0401 in Honda 1996 3.2tl mean?
Trouble code P0401 means: Exhaust gas recirculation - insufficient flow detected
How to make the airbag light go out after replacing air bags and module in a 97 Buick Rivera?
AnswerYou probably have to clear the computer error codes, this is generally what fires indicator lights. I don't know specifically about your car, but usually that is the case. This requires a code reader, plug it into the port (under the dash in most Fords - don't know about GMs) and let the reader cycle through 4 displays of the error codes. This will clear the computer and should make your light go off. If you don't have a code reader, I hear that AutoZone and some other parts stores will do this for you for free.If your car has been in a collision, and you replaced the described parts then you have another problem. It is very easy to scan the system and get the codes. Most likely one of the crash sensors not correctly installed. Or could be they replaced the module with a used unit. NOTE: once a car has been crashed with airbag deployment, the module is no good. Must have either a new one, or used one from a car that has not been crashed. Also seat belt sensor, or burned out bulb for pass side air bag-specially in Fords.
How do you fix serv error displayed on electronic readout on VT commodore?
you can buy a car diagnostic tool to clear the fault data, and a website is a good choice, allobd2.com
What does error code p1110 mean on 2001 Nissan pathfinder?
If your newer Nissan still uses the same codes as my 96 a P1110 is a cam positioner sensor malfunction. The problem could also be elsewhere in the cam positioning electronics. Dean
Resetting error code e 2006 Honda civic?
To reset the error code E on a 2006 Honda Civic, you can try disconnecting the negative battery terminal for about 10-15 minutes. This action will clear the error codes stored in the vehicle's computer. Alternatively, you can use an OBD-II scanner to clear the codes directly. If the error persists, it's advisable to check for underlying issues that triggered the code initially.
How do you reset engine light on 2002 Honda civic si?
To reset the engine light on a 2002 Honda Civic Si, you can disconnect the negative battery terminal for about 10-15 minutes, which will clear the error codes. Alternatively, using an OBD-II scanner to read and clear the codes will also reset the light. Make sure to address any underlying issues that triggered the engine light before resetting it to avoid further problems.
How do you clear a radio error code E00 on a Honda civic?
To clear a radio error code E00 on a Honda Civic, start by turning off the ignition and disconnecting the car battery for about 10-15 minutes. This can reset the radio system. After reconnecting the battery, turn the ignition back on and check if the error code has cleared. If the problem persists, consult your owner's manual or a professional mechanic for further assistance.
Where is the computer on the 1989 Honda Civic dx?
The computer or ECU for the 1989 Honda Civic DX is under a metal kick plate under the carpeting on the firewall of the passenger side of the car. If you are looking for the LED to read error codes, there is a hole in the kick plate that will allow you to read the error codes without removing it.http://i205.photobucket.com/albums/bb39/afullaytor/89Civickickpanel.jpg http://i205.photobucket.com/albums/bb39/afullaytor/89CivicComputer.jpg
How do you reset a 2003 Honda Civic airbag light?
To reset the airbag light on a 2003 Honda Civic, first, ensure that the vehicle's ignition is turned off. Next, locate the OBD-II port under the dashboard and connect an OBD-II scanner that can read airbag codes. After retrieving any stored error codes, clear them using the scanner. Finally, turn the ignition back on to see if the airbag light has reset; if the light remains on, there may be a persistent issue that requires further diagnosis.
How do you clear the error code on a radio of a 2004 Honda accord?
Depends on what the error code is.
How do you reset a Honda odyssey error e 2005?
To reset the error code on a 2005 Honda Odyssey, you can disconnect the negative battery terminal for about 10-15 minutes. This will clear the engine error codes from the ECU. After reconnecting the battery, turn on the ignition without starting the engine to check if the error light has gone off. If the error persists, it may indicate an underlying issue that needs to be addressed.
How do you fix error code 16 in a Honda Civic DX?
Error code 16 in a Honda Civic DX typically indicates a problem with the vehicle's fuel system, often related to the fuel pump or fuel injector issues. To fix it, start by checking the fuel pump's operation and ensuring it's getting power; if not, inspect the fuses and relays. Additionally, examine the fuel injectors for clogs or malfunctions. If these components are functioning properly, consider scanning for other related error codes or consulting a professional mechanic for further diagnosis.
What are the engine error codes for a 1990 Honda accord lx?
I found this helpful: http://hondaswap.com/reference-materials/88-ecu-error-codes-29109/ Good luck.
How to clear Samsung refrigerator error codes?
To clear Samsung refrigerator error codes, first unplug the refrigerator for a few minutes and then plug it back in. If the error code persists, consult the user manual for specific instructions on how to reset the error code or contact Samsung customer support for assistance.
Homda civic cheak engine light reset?
To reset the check engine light on a Honda Civic, you can use an OBD-II scanner to clear the error codes after diagnosing the issue. Alternatively, you can disconnect the negative battery terminal for about 10-15 minutes, then reconnect it. This method may reset the light, but it's essential to address the underlying problem to prevent it from coming back on. Always consult your owner's manual for model-specific instructions.
How do you reset the engine light for Honda crb?
To reset the engine light on a Honda CR-V, you can disconnect the negative battery terminal for about 15 minutes, which will clear the error codes. Alternatively, you can use an OBD-II scanner to read the codes and clear them. If the light returns, it indicates an ongoing issue that needs to be addressed. Always ensure that any underlying problems are fixed before resetting the light.
