answersLogoWhite

0

Use a line wrench and nothing else. Sometimes P'Blaster or penetrating oil can help. If you're good at torching things without melting them, you might heat the fitting and move it back and forth in very small increments with the line wrench. WARNING!! DOT3 Brake fluid is flammable and will boil even before igniting. DO NOT ATTEMPT to heat the fittings unless you have the proper protective equipment.

User Avatar

Wiki User

19y ago

What else can I help you with?

Continue Learning about Art & Architecture

Why do you have to pump on the brakes to get the brake lights to come on?

You need to adjust your brake light switch. It should be located on the brake pedal. Unplug the switch and loosen the nuts to adjust the button closer to the brake pedal.


What is the function of the brake?

Brake shoes are an integral part of the braking system of a motor vehicle. When a driver steps on the brake, the brake shoe is the mechanical part that he or she is ultimately controlling to bring the car to a stop. The backing of a brake shoe is a metal part, but the area that actually comes in contact with the brake is padded to provide friction to stop the car without damaging the brake itself. Brake shoes are found inside of drum brakes; disc brakes have calipers, which serve the same function in a slightly different way.


How do you re-set the auto parking brake when the rear pads have been changed on a Renault val satis?

some where along the parking brake cable is an adjusting nut. Loosen the nut and then lock it back in place with the other nut.


How do you replace the emergency brake release cable on a GMC suburban?

Your GMC Suburban emergency brake release cable is held in place with a swivel nut on each end of the cable. Loosen the swivel nut to remove the cable. Reverse the process to install the new emergency brake release cable.


How do you install brake pads on a 1992 Aerostar?

# Release the parking brake # Remove the cowl trim panel from the left side of the drivers compartment for access to the parking brake pedal # Pull back on the parking brake cable toward the control assembly (parking brake) and insert a 5/32 inch drill bit into the control actuator to lock the assembly into position # Its actually easier to pull the parking brake cable from under the vehicle but you will need an assistant to help you do this way. # Loosen the rear wheel lug nuts and raise and support the truck # Remove the brake calipers and the brake discs # Detach the parking brake cable from the actuator arm # Clean the parking brake assembly with brake cleaner # Remove the brake shoe retracting spring # Remove the adjusting screw spring and remove the adjusting screw # Remove the hold down springs from the shoes # Remove the parking brake shoes from the actuator

Related Questions

How can I adjust or loosen my bike brakes effectively?

To adjust or loosen your bike brakes effectively, you can use an Allen wrench to loosen the brake cable at the brake caliper. Then, adjust the barrel adjuster on the brake lever to fine-tune the brake tension. Test the brakes by squeezing the brake lever to ensure they are working properly.


How can I loosen the brake pads on a bike?

To loosen the brake pads on a bike, locate the brake caliper and use an Allen wrench to loosen the bolt holding the brake pad in place. Adjust the position of the brake pad as needed and then tighten the bolt back securely. Test the brakes to ensure they are working properly before riding.


Can you use brake fluid for tire shine?

No, brake fluid is damaging to the rubber of a tire.


When replacing your brake disc on a 96 accent what would be the best way to remove the hub without damaging the bearing and also reassemble without damaging the bearings what tools should be used?

You do not have to remove the hub in order to replace the disc brake pads or the rotor. The job is a difficult one without a press, probably best to take it to a garage, I work in one and wouldn't attempt this job at home!


How can I effectively loosen a brake caliper?

To effectively loosen a brake caliper, you can use a wrench to loosen the bolts that secure it in place. Make sure to support the caliper to prevent damage to the brake line. Once the bolts are loosened, gently wiggle the caliper to remove it from the rotor. Be cautious not to damage the brake line or other components.


How do you compress caliber on 97 Ford thunderbird do i need to remove or loosen something on rear brake assembly?

Loosen something on the brake if you tighten it will get worse screw caliper piston in or out with caliper tool. they are like that for the park brake function


How can I loosen the brakes on a bike?

To loosen the brakes on a bike, locate the brake adjustment barrel near the brake lever. Turn the barrel counterclockwise to loosen the brakes. Test the brakes to ensure they are not too loose or too tight. Adjust as needed for optimal performance.


How can I safely loosen bicycle brakes to improve their performance?

To safely loosen bicycle brakes for better performance, first locate the brake adjustment barrel near the brake lever. Turn the barrel counterclockwise to loosen the brakes. Test the brakes by squeezing the brake lever to ensure they are not too loose. Adjust as needed for optimal performance.


How to loosen a bike brake for better performance and control?

To loosen a bike brake for better performance and control, you can adjust the tension of the brake cable. This can usually be done by turning the barrel adjuster on the brake lever or caliper. Loosening the brake will allow the pads to sit further away from the wheel, giving you more control and a smoother ride.


How do you remove the rear calipers on a 1995 Sedan DeVille?

Remove rear wheels Loosen brake lines - but do not toally remove Loosen and remove 2 caliper mounting bolts remove brake line


How can I safely loosen the brakes on my bike?

To safely loosen the brakes on your bike, first locate the brake adjustment barrel near the brake lever. Turn the barrel counterclockwise to loosen the brakes. Test the brakes to ensure they are not too loose or too tight. Adjust as needed for optimal performance.


How does the Brake Piston Cube work?

The Brake Piston Cube is a cube-shaped tool used to retract brake caliper pistons in vehicles when changing brake pads. Its design allows it to fit into the caliper housing and apply even pressure to retract the pistons back into the caliper, facilitating easier brake pad replacement. By turning the Brake Piston Cube, the pistons are compressed uniformly without damaging the caliper or seals.