answersLogoWhite

0

first you remove the instrument cluster cover by taking out the headlight switch, rear defrost switch ect, take out all blank covers as well, use a Phillips screwdriver and remove all screws holding it on. take out the two screws holding the cluster to the dash. take out the five screws that hold the cover over the pedals in place. now reach up behind the cluster to the speedo cable, there will be a clip that as to be drepressed with your finger while you pull it back off the speedo guage. next you pop the hood and use a long Phillips head on a ratchet or a 13mm socket and remove the hold down bolt on the cable at the transmission. pull the gear head straight out and pull the other end through the firewall towards the front of the car. you will have to slacken the rubber boots at the firewall to do this. replacement is reverse.

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

How to Replace speedometer cable 1989 Toyota truck?

Speedometer cable replace 1989 toyota


How do i replace a faulty speedometer on a 1989 Volvo 740gl?

To replace a faulty speedometer on a 1989 Volvo 740GL, start by disconnecting the car battery for safety. Remove the instrument cluster by unscrewing the screws and gently pulling it out from the dashboard. Disconnect the speedometer cable and any electrical connectors, then replace the old speedometer with a new or refurbished unit. Reassemble the cluster, reconnect the battery, and test the new speedometer to ensure it functions correctly.


What part needs to be replaced for a 1989 Nissan Sentra when the odometer and speedometer are not working?

Most of the time, the speedometer cable breaks, and you replace it. The best way to find out, is to unscrew it from the transmission, and see if you can pull the cable out from the casing. If it checks out to be good, then it will be the drive gear inside the transmission, or the speedometer itself.


Where is the speedometer cable in a 1989 Mazda 626?

Back of the speedometer, through the firewall and into the top of the transmission.


How do you change the speedometer cable on a 89 Oldsmobile calais?

To change the speedometer cable on a 1989 Oldsmobile Calais, first, disconnect the negative battery terminal for safety. Then, remove the instrument cluster by unscrewing the necessary fasteners and pulling it out gently. Disconnect the old speedometer cable from both the transmission and the back of the speedometer, then replace it with the new cable, ensuring it is securely connected at both ends. Finally, reassemble the instrument cluster and reconnect the battery.


How do you fix speedometer for 1989 Honda Prelude?

To fix the speedometer on a 1989 Honda Prelude, first check the vehicle's speed sensor and wiring for any damage or disconnection. If the sensor is functioning properly, inspect the speedometer cable for wear or breaks. If needed, replace the cable or sensor, ensuring all connections are secure. Lastly, if the speedometer still doesn’t work, consider checking the instrument cluster for issues or consult a professional mechanic.


Where is the speedo cable on a 1989 s10?

The speedometer cable on a 1989 S10 is behind the steering wheel. The speed sensor is mounted on the transfer case tailshaft.


How do you lube speedometer cable 1989 Toyota truck?

Try blowing graphite down there.


How do you replace the speedometer cable for a 1989 silverado?

There is no cable....It is electric.....The speed sensor is on the transmission...Its called the VSS(Vehicle Speed Sensor)...Easy to take out and install...One bolt...Unplug the connector and remove the bolt and the sensor slides out.


How do you fix a 1989 Ford Laser ke speedometer that is not working?

probably a broken cable drive.


How do you repair the speedometer on a 1989 Z24 Cavalier?

i had the same car. its probally the cable that runs from the back of the speedometer to the trany. you have to pull out the instrument cluster. its not that hard.


How do you fix the parking brake of a 1989 volkswagen jetta?

To fix the parking brake on a 1989 Volkswagen Jetta, first, inspect the cable for any signs of wear or damage. If the cable is intact, adjust the tension by locating the adjustment nut under the center console and tightening it until the brake engages properly. If the cable is broken, you'll need to replace it by removing the rear wheels, disconnecting the old cable from the brake lever and drum, and installing a new one. After replacement, test the parking brake to ensure it holds the car securely.