The best way to remove the rear axle on a Polaris Hawkeye is to spray it with PB blaster. After waiting several hours or a day, simply pull the axle outward.Ê
remove axle bolt from spindle and push it through you may have to remove spindle if no clearance. remove factory tie strap clean and grease before replacing with new boot reassemble in reverse watch for pin on nut threads reversed on passenger side always consult technical manual and follow safety protocols
Remove the tire and wheel. Remove the brake assembly and rotor. Remove the axle end cap. The rear hub assembly will come off.
1984-1993 Jeep Cherokee XJ Rear Axle 1987-1993 Jeep Wrangler YJ Rear Axle 1986-1992 Jeep Comanche Rear Axle
The rear axle hub nut should be torqued to 260Nm or 192 lb/ft - this applies also to the front axle hub nut.
It would be best to consult the Factory Service Manual. Remove from the axle: tires, drive shaft, shock absorbers, parking brake cable and the soft brake hose. Remove the u-bolts and lower the axle.
To remove the rear axle on a Polaris Sportsman 500, start by lifting the rear of the ATV and securing it on jack stands. Next, remove the wheel and brake components, followed by the cotter pin and axle nut. Once these are removed, you can slide the axle out of the differential and remove any retaining clips or bolts from the wheel hub. Finally, gently pull the axle out from the side of the ATV.
To remove the rear axle bearing on a 2000 Polaris Expedition, first, safely lift and secure the vehicle. Remove the rear wheel and brake components to access the axle. Use a bearing puller or a suitable tool to carefully extract the bearing from the axle housing, ensuring not to damage any surrounding parts. Finally, clean the area before installing the new bearing.
To remove the rear axle on a 2000 Polaris Xplorer 400, first, ensure the vehicle is on a stable surface and secure it with jack stands. Remove the rear wheels and brake calipers for easier access. Next, disconnect the axle from the differential by removing the retaining clips and bolts, and slide the axle out of the wheel hub. Finally, ensure any necessary seals or bearings are replaced before reassembly.
To replace the rear axle bearings on a 2000 Polaris 6x6, start by lifting the vehicle and securely supporting it on jack stands. Remove the rear wheels and disconnect the brake components to access the axle. Use a socket to remove the axle nut, then slide the axle out of the housing. Replace the old bearings with new ones, ensuring they are properly seated, reassemble the axle and brake components, and finally reattach the wheels.
To replace the rear axle bearings on a 2003 Polaris Scrambler, first, elevate the rear of the ATV and remove the wheels. Then, take off the brake assembly and the axle nut, and slide the axle out of the housing. Use a bearing puller to remove the old bearings from the carrier, clean the housing, and press in the new bearings. Finally, reassemble the axle, brake assembly, and wheels, ensuring everything is properly tightened.
To replace the rear axle on a 2000 Polaris Xpedition 425, first, safely elevate the vehicle and remove the rear wheels. Then, disconnect the brake components and any other parts obstructing access to the axle. Remove the axle retaining bolts and slide the old axle out, replacing it with the new one. Reassemble by securing the axle in place, reattaching the brake components, and replacing the wheels before lowering the vehicle back to the ground.
To replace the rear axle on a Polaris Xplorer 400, start by safely lifting the vehicle and securing it on jack stands. Remove the rear wheels and brake components to access the axle. Disconnect the axle from the differential and any retaining clips or bolts. Finally, slide out the old axle and install the new one, ensuring all components are reattached securely before lowering the vehicle back to the ground.
To change the rear bearing on a straight axle Polaris, first, lift the vehicle and remove the rear wheel. Next, detach the brake caliper and remove the axle nut to slide out the axle. After that, use a bearing puller to extract the old bearing from the hub, clean the area, and install the new bearing using a bearing press or a suitable tool. Finally, reassemble all components in reverse order, ensuring everything is tightened to manufacturer specifications.
how to remove rear axle from 1988 f250 ford
To change the CV joint on the rear axle of a 2001 Polaris Sportsman 500, first, elevate the rear of the ATV and secure it on jack stands. Remove the rear wheel and brake caliper to access the axle. Disconnect the CV joint from the differential by removing the retaining clip and then slide the axle out of the hub. Replace the CV joint with a new one, reinstall the axle, and reassemble all the components in the reverse order. Ensure everything is tightened to the manufacturer's specifications before lowering the vehicle.
That might be the rear axle, it that is what you want to remove then you will need to remove the rear axle cover drain the fluid and the locate the center pin bolt and remove that in order to remove the center pin to get at axle c-clips then remove the c-clip for the axle you want to remove then slipe the axle out being careful not to distrub the axle bearing
buy the clymer manual first. there are clips on the inside of the cups remove them press the Ujoint out of the yoke. someone told me you need to install the rear drive shafts with the yokes/u joints the same on both sides lined up. Mine were from the factory. thanks