0
Slacken the wheel nuts and jack the car up
take the wheel off and undo the 'hub nut' (youll need someone to put their foot on the brake or leave it in gear)
undo the bottom arm from the hub
knock out the drive chaft from the center
undo the solid shaft piece and pull from the gearbox
make sure you have a bucket to catch the gearbox oil
re-fit with a new shaft in reverse order
stick the front of the car on axle stands and jack up the rear so it is level and top up the gearbox oil (this im unsure of how to do)
job done :)
What else can I help you with?
How do you replace the rear drive-shaft on a 96 tacoma reg cab?
Remove 2 small u-bolts from rear end yoke Pry drive shaft out of yoke Slide front end of drive shaft off front splines
How to drop 2000 s10 driveshaft to down on dolly?
What I believe your trying to ask is how to remove the drive shaft? If so than all you need is to remove the
Can you remove the drive shaft from the passenger side of 1996 Plymouth breeze to replace the output shaft seal without removing the strut?
Yes. You may also remove strut & steering knucle from car without separating them (if necessary) so you do not have to get an alignment.
Yamaha wr correct way to remove water pump impeller?
Remove the side case and the water pump. Remove the right side case, and remove the impeller and shaft. Holding the back side of the impeller shaft with a wrench on the flat spots, you can now twist the impeller off.
Turbo 350 transmission that leaks from rear of trans where drive shaft installs if you let it sit for more than a week how do you fix this?
replace tail shaft seal. to do this, remove drive shaft first. It helps if the front of the car is pointed down a steep hill. This way you won't loose any trans fluid.
Do you need to remove the drive shaft to change the starter motor on a peugeot 307?
Yes, on a Peugeot 307, you typically need to remove the drive shaft to access the starter motor. This is because the starter is located in a position that makes it difficult to reach without moving the drive shaft out of the way. It's important to follow the manufacturer's guidelines for the specific model and engine type to ensure a proper and safe installation.
Where is front abs sensor peugeot 406 2000?
ring on drive shaft with senser next to it. usual fault! cracked by rust ring on drive shaft. change shaft.
How do you fit peugeot 206 driveshaft seals?
remove the drive shafts, ensuring you remove the nut and horseshoe holding in the drivers side shaft. once they are out, you prise the seals out and tap in new ones en suring you get the news ones in the right way round
How do you change a Fiat Doblo drive shaft?
how to remove a drive shaft on a fiat doblo
How do you remove a drive shaft in 1999 Ford Taurus?
there is no drive shaft it's front wheel drive
Dodge Durango rear drive shaft removal?
How do you remove drive shaft from a 03 durango
How do you remove broken off flexible drive shaft from weedeater?
remove head pull shaft out
How do you remove the right front drive shaft on a 1990 LeBaron in order to remove and replace the power steering pump?
you can replace power stering pump without moveing drive shaft but its fiddly. to remove drive shaft undo 30mm nut in centre,undo bottom ball joint and pull strut out of way be ready to catch gear box oil.
How do you remove front drive shaft on trx 350?
To remove the front drive shaft on a Honda TRX 350, first ensure the ATV is on a stable surface and disconnect the battery. Remove any necessary covers or components to access the drive shaft. Then, unbolt the drive shaft from the front differential and the gearbox, ensuring to note the orientation for reinstallation. Finally, gently slide the drive shaft out of its housing.
Where is the Peugeot boxer speed sensor?
The speed sensor on a Peugeot Boxer is on top of the gearbox. It is near the driver's side drive shaft inner CV.
1948 ford drive shaft infohow do you remove the shaft.?
No proper man wants to be without his shaft
How do you replace a drive shaft center support bearing on a 2006 dodge ram megacab?
You must remove the rear drive shaft section and then remove the support.
