Wiper arms cannot be repaired, only replaced. The arm should come off by removing the nut at the bottom of the arm and the washer sprayer hose
Replace the wiper motor assembly. Fairly easy on these-- take off the wiper arms, and the motor is under the hood above the motor. You may need a mirror to see it. Three bolts and the electrical connections later, you can trade it in with some money for a reman part. Better yet remove the cover, there will be a metal tab that is bent. it is the park tab. bend it back towards the stop lever on wiper arm crank.
There is a square button where the wiper attaches to the wiper arm. Press the button and slide the wiper until it stops, about half an inch. Pull the arm away from the windshield and rotate the wiper slightly and it will unlock pull away from the wiper arm. No special tools required. Replacements are Anco Contour C24BB (one side) and C19BB (other side) or Valeo 900-24-9B & 900-19-7B. Other brands are available as well. Google can help you find the best prices, I suggest starting with Amazon.
Someone can minimize the chances of a wiper arm being detached by making sure some water is sprinkled on the windshield while operating the wipers. The water provides some lubrication for the wipers to move easily.
I don't have prints, but you take off the wiper arms and the vent cover across the truck below the windshield and there is the wiper assembly. The vent cover is held on with screws along the front edge in the engine compartment. If it is just the arm where it mounts on the assembly, you could always use some JB weld or epoxy and make it permanent.
The 2003 Hyundai Santa Fe has the most common hook-end wiper arms on both front and rear. See sources and related links below for installation videos. Also, purchase the replacement blades first and there will be additional instructions/illustrations on the replacement packages. Locate and press the tab or button where the wiper blade is inserted into the hook of the wiper arm and pull wiper blade out of hook. You may have to rotate and flex the blade to make enough clearance for the hook to pass through.
A wiper arm on a 2001 Honda Civic is screwed on. To remove it unscrew the mounting hardware and take off the wiper arm.
how do you replace wiper crank arm 2001 chevrolet impala?
How do you remove the wiper arms on 2001 Lincoln LS
Resubmit question describing the problem. Question too broad. What is it doing? What is it not doing? Wiper arm? Wiper blade?
To adjust the wiper arm on a 2001 Pontiac Aztek, first, lift the wiper arm away from the windshield and locate the nut securing the arm to the wiper motor shaft. Use a socket wrench to loosen the nut slightly, then reposition the wiper arm to the desired angle. Tighten the nut back securely and test the wipers to ensure they function correctly. Finally, lower the wiper arm back onto the windshield.
You don't have to remove wiper arm. The wiper blade will slide out, It has a clicker in the center of the blade that you have to slide it out. Look at it very carefully
To change the wiper blades on a 2001 Lexus LS 430, first lift the wiper arm away from the windshield. Press the tab on the underside of the wiper blade to release it from the arm, then slide it off. Align the new wiper blade with the arm, slide it into place until you hear a click, and then lower the wiper arm back onto the windshield. Repeat the process for the other blade, if necessary.
No, just replace it.
Under wiper arm flap is a grub nut, Undo nut and use a Wiper arm removal tool (there not expensive approx £10) Remove Arm and Replace with New
To remove the wiper blade on a 2001 Saturn L200, first lift the wiper arm away from the windshield. Locate the small tab or lever where the wiper blade connects to the arm, press or pull it to release the blade. Slide the blade off the wiper arm, and then simply attach the new blade by sliding it onto the arm until it clicks into place. Lower the wiper arm back onto the windshield once the new blade is secured.
You'll need a wiper arm puller, pretty easy takes less than 5 mins to pull
To change the wiper blades on a 2001 Audi Allroad Quattro, first lift the wiper arms away from the windshield. Press the release tab on the wiper blade's connector and slide the blade off the arm. Align the new wiper blade with the arm's hook, push it into place until you hear a click, and then gently lower the wiper arm back onto the windshield. Repeat the process for the other wiper blade.