answersLogoWhite

0

Remove serpentine belt

Remove any components obstructing any bolts on water pump

Ensure coolant cach container is in position because your engine coolant will come out

Remove any hoses from pump (if they are stuck on you can stick something under where hose attaches to pump and this will help fee up the seal). You may also have to remove pulley (easier to loosen bolts while serpentine belt is on).

Make sure bolts are re-installed in same position (you can put them in bolt holes of new pump then swap them to old pump before installing new part).

After removing pump (you may need to pry old pump off) clean all old gasket material off engine mating surface (scraper, flat screwdriver, die grinder are all tools that can be used).

Use brake cleaner on both engine and new pump mating surfaces to ensure they are clean, then use black silicone (or equal sealant) on both the engine and new pump (both sides of gasket).

After applying silicone install new pump on engine and place bolts in to hold it in position

Install bolts hand tight

USE PROPER TORQUE SEQUENCE AND SPEC TO TIGHTEN BOLTS- DO NOT OVER TIGHTEN BOLTS BECAUSE IT CAN DAMAGE GASKET.

Re-install all other parts and properly fill cooling system.

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

Where is ignition switch for 2000 Oldsmobile silhouette?

Can anyone please tell me where the ignition switch is located on a 2000 oldsmobile silhouette?


Anything bad about a 2000 Oldsmobile Silhouette?

No


Where is the thermostat located on a 2000 Oldsmobile Silhouette?

Follow the top radiator hose down to the engine. It is in the water outlet.


What is the fuel tank capacity for 2000 Oldsmobile Silhouette van?

25 gallons


How do you replace the thermostat on a 2000 Oldsmobile silhouette?

To replace the thermostat on a 2000 Oldsmobile Silhouette, first, ensure the engine is cool and disconnect the negative battery cable. Drain the coolant from the radiator and remove the upper radiator hose connected to the thermostat housing. Unscrew the thermostat housing, take out the old thermostat, and clean the mating surfaces. Install the new thermostat, reattach the housing and hose, refill the coolant, and reconnect the battery.


Can you install and amp in a 2000 Oldsmobile silhouette?

if you need mean an amp for a stereo ? yes you can


How do you reset the message center on a 2000 Oldsmobile silhouette?

all the messages are showing up on my 2000 olds silhoutte, why does it do this


How do you fix the lights in your center console for a 2000 Replace bulbs in center console of Oldsmobile Silhouette?

To replace the bulbs in the center console of a 2000 Oldsmobile Silhouette, first, remove any necessary trim pieces around the console by gently prying them off. Next, locate the bulb sockets and twist them counterclockwise to release. Replace the old bulbs with new ones, ensuring they are the correct type, and reassemble the console by reversing the disassembly steps. Finally, test the lights to ensure they are functioning properly.


Will a 2000 Oldsmobile silhouette driver information center fit in a 1998 silhouette?

1998, 1999, 2000 are interchangeable as well as the same parts from a Venture and a Montana. Same thing, different vehicle.


Where is the water pump located on 2000 Oldsmobile Silhouette?

Facing the front of the car, the water pump is on the left front of the engine. It is to the right of the battery. You can trace the hoses coming out of it if you lift the wiring harness.


How do you replace a 2000 Oldsmobile Intrigue GLS?

Replace it with a Ford!


How many oxygen sensors are there in a 2000 Oldsmobile Silhouette?

There are actually two oxygen sensors on a 2000 Oldsmobile Silhouette. There is one located in the exhaust system just before the catalytic converter. There is also another oxygen sensor in the air intake tube leading from the air filter.