Try using oxalic acid, also called wood bleach, on the water damaged area before attempting to stain the wood. If that removes the stain, sand the surface, use a wood conditioner or a clear stain as a first coat, then apply the colored stain. Once that's dry, apply a clear polyurethane for interior use, or a spar varnish for exterior use.
You should check the label on the specific product you're planning to use. If the label states it will adhere to wood with an existing coating, then it's fine to use even over an oil-based stain. (This is because once thoroughly dried, oil-based stains behave the same as water-based stains.) Some products, however, will require the existing stain to be stripped from the wood, or to apply a primer coat over the existing finish before applying new stain.
No Stain is applied to wood before any sort of sealer stain enhances the color of wood to bring out grain different densities of wood absorb the stain at different rates paint, varnish, lacquer seal out water after a stain is applied. Lately stain is hard to find the one step idea stain,sealer, clearcoat all in one is the norm the results are so much inferior i have no idea how they can sell that junk. perhaps that is why you can find so much nice furniture on trash day
You can stain balsa wood.
Wood stain is abosorbed into the wood, so the wood takes on the color of the stain. This is why the features of the wood are still visible, unlike with paint.
If you paint over the "weathered" paint, it will chip and cause the stain to come off. Also, the stain needs a clean sanded surface in order for the wood to absorb it. Otherwise, there is no reason to use stain.
i think it's called a water stain, it can happen to about everything, so i think it would be called a water stain on wood.
You should check the label on the specific product you're planning to use. If the label states it will adhere to wood with an existing coating, then it's fine to use even over an oil-based stain. (This is because once thoroughly dried, oil-based stains behave the same as water-based stains.) Some products, however, will require the existing stain to be stripped from the wood, or to apply a primer coat over the existing finish before applying new stain.
Wood stain MUST penetrate the grain of the wood or it doesn't color. clear coats like Varnish or Urethaneare designed to seal over the stain "color" & keep the wood from being "stained" by all the dirt & spills it endures over time. If you don't sand the old finish off evenly it will keep the new stain from penetrating and it will also allow the stain to penetrate in areas where the old varnish was worn or damaged but not in others making the new stain blotchy & uneven. A good quality urethane is far better and easier to apply than Varnish. .
You can stain balsa wood.
No Stain is applied to wood before any sort of sealer stain enhances the color of wood to bring out grain different densities of wood absorb the stain at different rates paint, varnish, lacquer seal out water after a stain is applied. Lately stain is hard to find the one step idea stain,sealer, clearcoat all in one is the norm the results are so much inferior i have no idea how they can sell that junk. perhaps that is why you can find so much nice furniture on trash day
Wood stain is abosorbed into the wood, so the wood takes on the color of the stain. This is why the features of the wood are still visible, unlike with paint.
Wood stain is for sealing and emphasising the natural colour of wood
How you can get a wood stain out of a white t-shirt depends on whether the stain is oil or water-based. For oil-based wood stains, use mineral spirits and for water-based wood stains, use acetone. Blot the stain from the edges and work your way in towards the middle but do not rub. Wash the t-shirt on a hot laundry cycle, between 60 and 90 degrees.
soak it bleach and soap and hot water
If you paint over the "weathered" paint, it will chip and cause the stain to come off. Also, the stain needs a clean sanded surface in order for the wood to absorb it. Otherwise, there is no reason to use stain.
NEGATIVE IT WILL PEEL
It can be very difficult to try to lighten stain on wood once it is applied. The best way to do it is to sand the wood down and start over.