0
What else can I help you with?
What is the purpose of the spark plug?
It ignites the compressed air/fuel mixture.
Where are check valves located?
Located in master cylinder and prevent air from being drawn in past the wheel cylinder cups when the brakes are released
CAN A VW Bug 4-cylinder air cooled eng run with a bad ignition condenser?
No, it will not run.
What enters the cylinder during the induction stroke on a diesel engine?
In an internal combustion engine with a carburettor a mixture of air and atomised fuel is drawn into the cylinder. If the engine is fuel injected compression ignition engine then air is drawn in, the fuel is introduced just before top dead centre of the compression stoke. If you mean intake stroke, then the answer is air.
What do glow plugs do in a diesel engine?
They preheat the air in the cylinder to make starting easier. they actually heat the diesel fuel to make starting easier
How much air does a 3 ltr dive cylinder hold?
A 3-liter dive cylinder holds approximately 3 liters of air at the cylinder's rated pressure. The actual amount of breathable air will depend on the pressure in the cylinder; for example, at a common pressure of 200 bar, a 3-liter cylinder contains about 600 liters of air at sea level conditions. This is because gases expand to fill the volume of their container, and the compression increases the density of the air inside the cylinder.
What is multistage air compressor?
These are compressors with more than one cylinder, usually of different sizes. The first cylinder takes in air at normal pressure and compresses it some. Then it releases the slightly compressed air to the second cylinder which takes it in and compresses it more. This repeats with each following cylinder. You can get much higher pressures this way than is practical with just one cylinder.
How much pressure will compressed CO2 create when released in an air cylinder?
Whatever amount of pressure was used to compress the CO2 originally, can be reached (or nearly reached) when it is released into an air cylinder.
Why not diesel engine is spark ignited?
A gasoline injects fuel into the cylinder as it is filled with air, compresses it, then ignites the spark plug to trigger the power stroke. In a diesel engine air is compressed up to 3 times more causing a much higher cylinder temp. Once the air in the cylinder is hot diesel fuel is injected directly into the cylinder and is ignited by the high temperature.
How does a pneumatic cylinder work?
penumatic cylinder work by compressed air that a comressor compress air in a closed cylinder which ther is no way air to get out exept it bush piston which is instaled transition fit with cylinder and in return path we use spring or compressed air
How do you change master cylinder on 2003 Oldsmobile alero?
unplug electrical connector for the fluid level warning switch. remove as much fluid as possible from master cylinder, with a syringe or similar to suck out the fluid. take off the brake lines to the cylinder. pull lines away from cylinder, and cap the ends so you do not loose fluid from the lines. remove the nuts attaching master cylinder to firewall. pull the cylinder off of the studs to remove it. bench bleed the new cylinder before installing it. (that means to remove all air trapped in cylinder). fill up new cylinder with new fluid, and push on plunger of cylinder to release the air. do this until no more air bubbles are presant in cylinder. if no fluid is lost from the lines and all the air is out of the cylinder. there is no need to bleed all the brakes just bleed by remove lines at cylinder if needed. GOOD_DAY!
What is an air tank?
a air tight compressed cylinder that carries air
Is the purpose of Supercharger?
To increase an engines Hp/Tq, by increasing it's volumetric efficiency ( how much air/fuel is in the cylinder).
How power cylinder connection rod and cylinder block works in stirling engine?
The power cylinder works on the principle that heated air expands, and cooled air contracts. After the displacer moves the air to the hot side, the air heats up and expands (after a small delay) and pushes out the power cylinder, which in turn pushes the connecting rod and the crankshaft. When the displacer has moved the air to the cold side, the air contracts, pulling the power cylinder down, pulling the crankshaft. The power cylinder is 90 degrees 'behind' the displacer, due to the delay in expanding of the air after heating.
How do you bleed the clutch line if there is no bleed screw?
Fill your slave cylinder using a hypodermic syringe (won't take much) and install it. Before you tighten the connection to the slave cylinder, bleed the air out of the line by filling the reservoir and pumping the air out until it runs clear. After it runs clear, tighten the connection to the slave cylinder.
Functions of cylinder head valves?
To open and close at the proper time to allow air/fuel mix to enter cylinder and for spent air/fuel mix to exhaust the cylinder.
How do you clean oil from a compressed breathing air cylinder?
To clean oil from a compressed breathing air cylinder, you can flush the cylinder with clean air to remove any residual oil. You can also use a specialized cleaning solution designed for air cylinders to remove oil contamination. It is important to follow proper safety procedures and regulations to ensure the cylinder is safe for use with breathing air.
