0
Is there a product that will seal tacky oil based stain on cabinets?
Wiki User
∙ 11y ago
No, you need to remove the tacky coating before anything will stick properly.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What do you do about tacky stain-repair job after trying to blend in several dog-scratch marks on a dark walnut varnished table using stain and now the table is tacky?
I would remove the stain from the entire piece (leg or top) and then carefully re-stain it properly.
Wood deck tacky after using a waterbased semitransparent stain?
you need to wipe the excess stain off the deck with a clean rag. It will never dry and it will float to the top of the sealer
Can you skim coat over gloss paint?
Assuming you are using a dye-based spray on stain, yes, if the gloss is already set up and scuffed! However,while spraying or applying, gloss is too wet/tacky to work with between coats! As I do at work using Acrylic Polyurethane paints onto cabinet parts, your best bet is to apply a first coat of satin, stain over that, then a final coat of satin to seal the stain! (NEVER apply gloss over an unsealed dye based stain, as the heavy material will have a tendency to pull your stain and make the color look uneven!) As soon as the satin is flashed off (10-30min, depending on paint and temp.) you can apply your gloss. This is the method we have used for decades on HIGH quality cabinets!
Can you varnish over tacky stain?
Never apply a coating over a surface that hasn't fully cured. If the stain is "tacky" then it either has been applied way too thick for a penetrating stain, it was applied in high humidity, or it has not been allowed to dry sufficiently. Either allow sufficient time for the stain to dry, or if it's just not drying, remove the stain and reapply under the correct conditions before applying a clear coat.
Is Behr vs Cabot deck stain best?
No question. Consumer reports has 3 year data for the Cabot stain and it was rated at greater than 80 percent (very good). There is only one year data for the Behr stain. There are many complaints about the Behr stain, and many contractors recommend the Cabot stain over Behr. I just used Cabot stain and in some areas I applied two coats to get the look it needed to blend the color. Both the one coat and two coat areas are GLOSSY and TACKY. This does not look good. I tried to rub it with mineral spirits, but that did not help. I have found that in the past, this was a better stain, but to reduce VOCs, they change the product. IT DOES NOT WORK WELL. I called Cabot to complain and all they can say is that I must of applied it to heavy. If I apply it any lighter, it just wont have any color to it. I used 9202 ceder. The tacky surface did not improve after a week and it is collecting dust. Very bad outcome. I expect to sand the deck down next. UPDATE. I sanded it down with a floor sander, 80/120 grits. I used Superdeck from ACE. This is the best stain I have seen. I used the stain for pressure treated wood, cedar color. Looks great. Very pleased.
How long does it take for stain to dry completely?
Depending on the stain technique it can take anywhere from 2 to 24-hours for the stain to dry. For cabinets, you should wait the entire 24-hours to make sure the stain is not still tacky and to prevent smudges on the finish.
What do you do about tacky stain-repair job after trying to blend in several dog-scratch marks on a dark walnut varnished table using stain and now the table is tacky?
I would remove the stain from the entire piece (leg or top) and then carefully re-stain it properly.
What do you do if you failed to wipe of the stain and the finish is tacky It was an oil based stain applied 20 hours ago?
If it is just the stain with no top coat or sealer on it, just wipe it down with a rag and mineral spirits, paint thinner, Lacquer thinner, anything to put the stain back into solution.
Wood deck tacky after using a waterbased semitransparent stain?
you need to wipe the excess stain off the deck with a clean rag. It will never dry and it will float to the top of the sealer
Do you spray texture on the walls before or after you hang kitchen cabinets?
After you hang the cabinets. Tape off the cabinets and anything else before you spray. However, sprayed texture looks REALLY tacky on the walls unless it is artfully done by a decorative painter. Why don't you just paint?
Can you skim coat over gloss paint?
Assuming you are using a dye-based spray on stain, yes, if the gloss is already set up and scuffed! However,while spraying or applying, gloss is too wet/tacky to work with between coats! As I do at work using Acrylic Polyurethane paints onto cabinet parts, your best bet is to apply a first coat of satin, stain over that, then a final coat of satin to seal the stain! (NEVER apply gloss over an unsealed dye based stain, as the heavy material will have a tendency to pull your stain and make the color look uneven!) As soon as the satin is flashed off (10-30min, depending on paint and temp.) you can apply your gloss. This is the method we have used for decades on HIGH quality cabinets!
Can you varnish over tacky stain?
Never apply a coating over a surface that hasn't fully cured. If the stain is "tacky" then it either has been applied way too thick for a penetrating stain, it was applied in high humidity, or it has not been allowed to dry sufficiently. Either allow sufficient time for the stain to dry, or if it's just not drying, remove the stain and reapply under the correct conditions before applying a clear coat.
Is Behr vs Cabot deck stain best?
No question. Consumer reports has 3 year data for the Cabot stain and it was rated at greater than 80 percent (very good). There is only one year data for the Behr stain. There are many complaints about the Behr stain, and many contractors recommend the Cabot stain over Behr. I just used Cabot stain and in some areas I applied two coats to get the look it needed to blend the color. Both the one coat and two coat areas are GLOSSY and TACKY. This does not look good. I tried to rub it with mineral spirits, but that did not help. I have found that in the past, this was a better stain, but to reduce VOCs, they change the product. IT DOES NOT WORK WELL. I called Cabot to complain and all they can say is that I must of applied it to heavy. If I apply it any lighter, it just wont have any color to it. I used 9202 ceder. The tacky surface did not improve after a week and it is collecting dust. Very bad outcome. I expect to sand the deck down next. UPDATE. I sanded it down with a floor sander, 80/120 grits. I used Superdeck from ACE. This is the best stain I have seen. I used the stain for pressure treated wood, cedar color. Looks great. Very pleased.
Can food be tacky?
yes, food can be tacky
What rhymes with wacky?
"tacky" and "jackie"tacky
Who was Chief Tacky?
I want to know who is chief tacky
When did Tacky's War happen?
Tacky's War happened in 1760-05.
