I would say you have broken teeth on it, or your battery may be getting too low, while your key is in the ignition in the on position, take a screwdriver and touch the B+ wire on the starter solenoid ( may take a few tries but should start)! I would also advise that you get it replaced!
Should be at the lower rear end of the engine Remove the - battery cableRaise and support vehicleRemove wires from starter solenoid at top of starterRemove starter mounting boltsRemove starter
Absolutely not. The starter gear must fully disengage the flywheel gears when you release the starter. Otherwise when the engine starts the starter will continue to be turned by the engine.
It's quite easy.You have to disconect the battery first.Then go under the car and the starter is located where the engine meets the transmission.There are only 2 bolts.They are straight up and down.Take the bolts out and the starter will drop(will not fall all the way out).Then disconect the wires.Now the fun part you have to get it out of the engine compartment.To do this you have to just keep trying different angles until it comes out.Then to re-install just reverse the process.It is very important to disconect the battery before you do anything(Risk of sever electric shock).
The 1995 Pontiac Grand Am starter relay switch can be found on the firewall in the engine compartment. The starter relay switch will be on the drivers side of the firewall.
on passenger side near rear of motor. Here's a writeup. http://hubpages.com/hub/Starter-Removal-1999-Pontiac-Grand-Prix
The starter motor kicks out before the engine starts to prevent damage to the starter and the engine itself. If the engine fails to start after a few attempts, the system disengages the starter to avoid overheating or overloading the starter motor. Additionally, this mechanism helps ensure that the engine is not cranking indefinitely without ignition, which could lead to battery drain or mechanical issues.
the starter on all Pontiac 326-455 engines are on the drivers side of the engine.
The 2000 Pontiac Firebird starter can be found on the right hand side of the engine. The starter will be near the back of the engine.
where do the wires on the starter go on a 1977 pontiac 400
The starter, upon activation, has a gear that is forced onto the engine's flywheel's gear to turn the motor over. Upon engine start or release of the start voltage the starter gear disengages.
on the bottom side of the engine.
What year? What year? What engine?
To replace the starter on a 2003 Pontiac Vibe, first disconnect the negative battery terminal to ensure safety. Then, remove any necessary components for access, such as the engine cover or air intake. Unbolt the starter from the engine, disconnect the wiring harness, and remove the starter. Install the new starter by reversing the process, ensuring all connections are secure before reconnecting the battery.
A starter clutch, also known as a one-way clutch or sprag clutch, allows the engine to start by engaging the starter motor while preventing the engine from driving the starter. When the starter motor turns, the clutch engages, allowing the engine to crank. Once the engine starts and exceeds a certain speed, the clutch disengages, preventing the starter from being driven by the engine's rotation, which protects the starter motor from damage. This mechanism is crucial for ensuring smooth engine starts and preventing backflow of energy to the starter system.
A starter motor is an electric motor that initiates the engine's operation by turning the flywheel, allowing the engine to start. It is powered by the vehicle's battery and engages when the ignition key is turned. Once the engine is running, the starter motor disengages automatically, as it is not needed during normal operation. Starter motors are essential components in most internal combustion engine vehicles.
To replace the starter in a 1969 Pontiac Firebird, first disconnect the battery to ensure safety. Then, locate the starter, which is usually mounted on the lower passenger side of the engine. Remove the wiring harness and the mounting bolts holding the starter in place. Install the new starter by reversing the removal process, making sure to reconnect the wiring securely before reconnecting the battery.
It is between the engine and transmission. It is closer to the driver side, under the engine.