answersLogoWhite

0

Negative, that way if hit a ground while on pos bolt it wont short out.

User Avatar

Wiki User

19y ago

What else can I help you with?

Continue Learning about Art & Architecture

How do you change starter on ranger 2002?

Jack and support front or use ramps to elevate front of vehicle. Disconnect the negative battery terminal. Remove electrical connections and then the mounting bolts, be careful, the starter is very heavy. Align and install mounting bolts, then reconnect electrical connectors, and reinstall negative battery cable. It might be a good time to disconnect the positive battery terminal as well, use a terminal cleaner to clean the battery terminals, the insides of the clamps, then spread dielectric grease over terminal, reconnect all and snug.


What side does electrons flow from in a battery?

Outside the battery:The path for conventional current goes from the positive terminal (+, usually a red wire) to the negative terminal (−, usually a black wire).A wire's electrons flow from the negative (−) terminal to the positive (+) terminal.Since the current forms a continuous a loop in the same direction, the direction inside the battery is "backwards".Inside the battery:Conventional current flows from the negative (−) terminal to the positive (+) terminal.Positive ions flow from the negative (−) terminal to the positive (+) terminal.Negative ions flow from the positive(+) terminal to the negative (−) terminalConventional current assumes that all flowing charges are positive. It simplifies the situation because it hides the more complicated electrons, positive ions, and negative ions.


What is the procedure of the baterry?

The vehicle battery's main purpose is to supply power for the starting system and to power some accessories when the engine is not running. The proper procedure for changing or installing a battery... remove the battery cable first from the negative battery terminal, then from the positive. Install opposite, attach the positive cable lead, then the negative.


How do you hook cables to battery?

you hook the positive cable,(usually the red) to the positive battery terminal first then you hook the negative cable(usually black) to the negative terminal if you hook it the other way you can get sparks or arcing that can cause damage or a fire PS: if both cables are same color, the negative cable is the one bolted to the frame or the engine.the poitive is bolted to the solenoid or starter


What color is positive on a car battery?

Normally red or brown. The battery has a + stamped into it by the positive terminal. Follow the wires, on a modern car the positive will go to the alternator and starter. The negative wire (easier to follow) will go to the body/engine block

Related Questions

Should you disconnect the positive or negative battery terminal first - 45k?

Always the negative cable first.


When removing the battery leads from the terminals you do what first?

Disconnect the negative - terminal first, then the positive + terminal. Unfasten the battery hold down clamp. When reinstalling the terminal connections connect the positive terminal first.


What does the negative terminal of a battery have?

The negative terminal of a battery has a - sign and positive terminal has a + sign.


Does energy flow through the negative or positive of a battery?

Energy flows from the negative terminal to the positive terminal of a battery.


Which battery terminal do you hook up first?

Connect the positive + cable first and negative - last. When disconnecting them disconnect the negative - first and positive + last.


Does the positive end of a battery go to the positive or negative end of the terminal?

The positive end of a battery goes to the positive end of the terminal. In retro spec, the negative end of a battery goes to the negative end of the terminal.


How do you remove the battery on a 1999 Ford Escort ZX2?

Disconnect the negative terminal first. Then disconnect the positive terminal. Pull the ends straight up. Unbolt the top of the battery frame and lift up the cover on the battery.


When you charge a car battery what do you disconnect first?

When charging a car battery, you should always disconnect the negative terminal first. This helps prevent any short circuits or sparks that could occur if the positive terminal is disconnected first while the battery is still connected to the car's electrical system. After charging, reconnect the positive terminal first before reconnecting the negative terminal.


How do you replace the positive battery cable on a 1996 Ford Aspire?

To replace the positive battery cable on a 1996 Ford Aspire, first disconnect the negative battery terminal to ensure safety. Then, remove the bolt securing the positive cable to the battery terminal and detach the cable. Install the new positive cable by connecting it to the battery terminal and tightening the bolt securely. Finally, reconnect the negative terminal to complete the process.


What happens when you inadvertanly crossed the positive battery terminal from a negative to a positive and a positive to a negative.?

What happens when you inadvertently crossed the positive battery terminal from a negative to a positive and a positive to a negative.?Read more: What_happens_when_you_inadvertanly_crossed_the_positive_battery_terminal_from_a_negative_to_a_positive_and_a_positive_to_a_negative.


How do you charge battery on suzuki intruder?

To charge the battery on a Suzuki Intruder, first, ensure the motorcycle is turned off and disconnect the battery terminals, starting with the negative (black) terminal followed by the positive (red) terminal. Use a compatible battery charger, connecting the positive charger lead to the positive battery terminal and the negative lead to the negative terminal. Set the charger to the appropriate voltage and amperage, and allow it to charge until full. Once charged, reconnect the terminals in reverse order, positive first and then negative.


How do you replace positive battery cable on a 2007 Chevy Aveo?

To replace the positive battery cable on a 2007 Chevy Aveo, first, disconnect the negative battery terminal to ensure safety. Then, remove the positive terminal by loosening the nut with a wrench and pulling the cable off the battery post. Install the new positive cable by securing it to the battery terminal and tightening the nut. Finally, reconnect the negative battery terminal, ensuring all connections are secure.