0
Adv, Gear Systems- 1.Provide Positive Drive without slip. 2. Suitable for high speed , high torque & high power transmission. 3.Properly designed & properly maintained gear system can run over decades. 4. very high transmission ratio is practicable. 5. Compact machine train in limited space. Dis Adv. Gear Systems- 1. Needs Proper Lubrication System. which involve high cost. 2. Needs Proper alignment- misaligned gear train will demage within very short time. 3. misaligned gear mesh or lack of lubrication will make noise & vibration. 4. Spare gear is costly and proper replacement gear is difficult to procure in many cases it is available only from OEM source. 5. Require skilled technician to maintain. Adv. Belt system. 1. It is a simplier system than Gear System. 2. It do'nt need lubrication. 3.Belts can be replaced easily. 4.Belts are easily available in market. 5. Belts can accomodate some mis-alignment. Dis Adv. Belt System- 1. Not suitable for high speed, high torque or high power transmission. 2. Belt life is very short so needs frequent replacememt. 3. Belt Slip causes poor power transmission, heat generation, pully wear. 4. Open belt is unsafe. 5. Require more space so it can'not be used in a compact system. Answer by - Engr A Z M Aurangazeb , email- aaurangajeb&gmail.com or abu.aurangazen&mobilbd.com
What else can I help you with?
What are some disadvantages of manual driving?
If you want to overtake someone you don't have to worry about which gear to select to make sure you get round them in time. Just floor it and the automatic gears do all the work for you!
Explain Synchronizer unit of a gear box?
The transmission input shaft has gears on it that mesh with the different drive gears. It is spun by force from the engine, as you select different gears with the shifter, there are different sets of gears being meshed together inside transmission. The synchronizers ensure that the gears being meshed together are turning at the same speed, thus resulting in a smooth shift and no damage to the gears.
Where can you get Ford Aspire spider gears?
One can purchase Ford Aspire Spider gears directly through the Ford dealership. These parts can also be purchased at auto part stores.
Your car starts but won't shift gears when running Also when ist not started you have all gears but when you push the clutch in to start it it learches forward What could be wrong?
Most likely the clutch master cylinder and/or slave cylinder has went out. It's a good rule of thumb to replace both at the same time to save frustration later on. A hydraulic clutch system works on the same principle as your brake system. Its very important that after replacing the slave and master cylinder that you properly bleed all air from the hydraulic lines to ensure proper clutch pressure.
What causes loss of all forward gears in 2wd avalanche with automatic trans.?
the clutch or clutches in the transmission are bad,even if changing the tranny filter helps the forward gears will not be right and quit again
What disadvantages of spur gears?
Advantages - Spur gears are simplest, easiest to design and manufacture and disadvanages i dunno :)
What are the advantages and disadvantages of using a mountain bike without gears?
Advantages of using a mountain bike without gears include simplicity, lower maintenance, and potentially lower cost. Disadvantages may include limited speed options, less efficiency on varied terrain, and more physical effort required when riding uphill.
What are the advantages and disadvantages of syncromesh?
Advantage: much easier to select between gears without having to double-clutch. Disadvantage: for a given gear-pack size, synchro'd gears are weaker.
What are the advantages of using a hub gear system in bicycles?
A hub gear system in bicycles offers advantages such as low maintenance, protection from weather elements, and the ability to shift gears while stationary.
Why might compound gear train be better than two gears alone?
Because the speed is decreased less from an equal gear ratio.
What are the disadvantages of fixed landing gears?
high drag
What are the advantages of using an internal hub gear system in bicycles?
The advantages of using an internal hub gear system in bicycles include smoother gear shifting, protection from external elements, low maintenance requirements, and the ability to shift gears while stationary.
What are the advantages and disadvantages of using high gears versus low gears on a bike?
Using high gears on a bike can make pedaling easier and faster, which is advantageous for riding on flat terrain or going downhill. However, it can be harder to pedal uphill or start from a stop. On the other hand, low gears make it easier to pedal uphill or start from a stop, but can make it harder to pedal at high speeds or on flat terrain.
What are the advantages of using internal bike gears over external gears for cycling?
Internal bike gears offer several advantages over external gears for cycling. They are more protected from damage, require less maintenance, provide smoother shifting, and are better suited for riding in various weather conditions.
What is better halo 3 or gears of war 2?
Halo has much more of a fanbase. It also has an extremely well structured multiplayer matchmaking system. Forge, Custom Games, and Theatre are also advantages against Gears of War 2.
What are the advantages of using a Shimano internal hub for bicycle gears?
Using a Shimano internal hub for bicycle gears offers advantages such as low maintenance, protection from weather elements, and smooth shifting.
What are the 3 gears to make up a gear system?
The 3 gears are driver, driven, and idler gears.
