0
The underhood label on mine says 0 degrees for both manual and auto trans. I just set mine to 0, but it doesn't seem to be running right. I've heard there's a timing wire that needs to be unplugged before checking the timing. If anyone knows what that is, it would help us both out.
If your motor has the hei with the external coil, you remove the four pin connector on the dist. leave the other one connected. This shuts off the est and you should be able to time the motor.
What else can I help you with?
How do the timing marks set on the timing gears 1969 dodge dart 225 slant six?
To set the timing marks on the timing gears of a 1969 Dodge Dart with a 225 Slant Six engine, first ensure the engine is at top dead center (TDC) on the compression stroke for cylinder one. Align the timing mark on the crankshaft gear with the mark on the timing cover, and then align the camshaft gear's mark with the corresponding mark on the timing chain or cover. This ensures that both the crankshaft and camshaft are properly synced for optimal engine performance. After aligning, double-check the marks before reassembling any components.
How much is a 1969 dodge dart gt convertible with 318 cid motor and 4 speed transmission worth?
What is the condition
1969 dart had 340 now 318 in car used 340 motor mounts when i switched used oil pan that was on 318 the center link is rubbing oil pan what is my problem motor mounts or oil pan?
the motor mounts should be the same, as the 318 is the same block as the 340, the only thing I can think of is the oil pan was different on the 340.
Will a 440 v8 fit in a 1969 4 door dodge dart?
yes but it may take a few mods. steering may be an issue
Where is the timing to be set at for a 1962 Chevy 283 engine?
each engine is different but give it to a mechanic and let him set it to somewhere around 32 - 34deg total timing. This will take the vacuum of the engine into play as well. If you don't want to spend the money take the vacuum off the carb and set to 4-6 deg on your timing cover. This will be pretty close to the same setting. If you have difficulty starting turn counter clockwise just a hair and you should be ok.
What year and model did Chevy make a hemi motor for?
Chevy never made a hemi motor
What is the timing specs for a 1969 396 Chevy big block?
6 degreed advanced or BTDC.
What year is the Chevy motor with the casting numbers of gm 3970010?
it is a 1969-1979 motor it was used in cars, trucks, and vettes
What gm motor do i have the engine casting numbers are 3970020?
1969-1973 chevy 307
Who made a 468 cubic inch motor?
Chevy put one in the 1969 Chevelle.
Did the 1969 Chevy C 10 pickup come with a big block motor?
There was a 396 available in all Chevy trucks from 1968 - 1970.
What causes a 1969 350 Chevy to misfire?
its either ur timing belt or ur sparkplug wires r wrong
How do you remove a wiper arm on a 1969 Chevy Nova?
pry it up off of the motor splines to take it off.
Where can you find an engine diagram for a 1969 Chevy 396?
Buy a motor manual at your local auto parts store.
What is the correct timing for a 1969 Pontiac le mans 350 motor?
Pontiacs typically like 12-14 degrees initial timing. It's a good starting point.
What degree do you set the timing on a 1969 Chevy 350?
I would set it at 10 BTDC with the distributor vaccum unhooked while setting timing. 10 to 13 degrees is what the factory recomends.
Timing on 396 in 1969 Chevelle?
6, to 8 degrees, advanced. Advance it as far as you can, until the motor pings on acceleration, or, under load.
