0
I used an SKF 30205J2/Q bearing and CR 692369 seal. Russ
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How long does it take to replace a wheel bearing hub in a 96 blazer?
With the proper tools and knowledge, 1 hour.
Are Triangle Trailer tires good tires?
As a Small town retail store owner, we have had good luck with the Triangle trailer tire. It might not last as long as a Goodyear Marathon but for the money its a good buy.
How do you fix throw out bearing on 2000 Toyota Tacoma?
You replace it. As long as you have the transmission out, you might as well put the clutch and pressure plate in also.
How do you repack front wheel bearings on a Toyota 4runner?
Pull the wheel front and rear bearing and clean out the old grease. You dont have to be perfect but do a good job. Then clean all the parts of as much of the old greas from the outside and make note of the order for the parts. Pull the seal and replace this part. Now all is clean and ready to re-grease. to pack the bearing you can do it old school or new school. Us old school will place a wad of grease in the palm of one hand and hold the bearing in the other. Then with a push and slide motion you can scrape the edge of the grease and shove it in one of the cracks of the bearins. This forcing motion will shove new grease in the bearing on one end. and the old grease out the other. When new grease is coming out the other end then turn the bearing and do the next ecction of the bearing. Its a long dirty process but it gets the job done. Do bother bearings and then put the parts back together in the back side of the hub. Prior to doing this put a good amount of grese on the bearing surfaces inside the hub. You don't have to plug it up but you dont want the new grease running out the bearing either. Then reinstall the seal and lube the shaft on the car. Reinstall the hub and then do the same thing on the front bearing. New school is the same except you use a bearing packer from a store. All the auto places and even wal mart will carry it. You place the bearing in a holder and use a grease gun to pack the bearing. It is time efficient and once you start to pump the grease you see the old come out the sides. Once all the old is out and new stuff starts coming out you are done. Nice and neat the first time but it uses a bit more grease that can go to waste. Just be careful. Since grease LOVES to hold dirt and debris you need to be super careful after you use it so it stays clean for next time. I just pulled my 96 Toyota bearings and the race and bearings look new. I change the grease about every 50 000 miles and I now have 325000 on the vehicle. So its worth the time.
How does one take offf a steering wheel on a 1982 Chevrolet TK model PK body style 12 ton with a 305 small block engine?
You will need a puller to remove the steering wheel, after you remove the nut and snap ring in the center of steering wheel. Ther are two holes in the wheel that are threaded. Install puller on center shaft, and screew 2 long bolts through the puller and into the holes on wheel.
What can happen if rear wheel bearing is not replaced?
If you do not change a bad wheel bearing the bearing will cut a groov in the axle.If it goes on long enough the axle will have to be replaced.It could also ruin the axle housing.Then you would have to replace the rearend.
How long does it take to replace a front wheel bearing on a 2007 Montana?
two minutes
Is it safe to drive with a bad wheel bearing?
Not knowing how bad the bearing is, I can't say how long it will last before the wheel falls off. Drive to your local garage for repair and don't take the highway.
How long will the wheel last with a damaged wheel bearing?
It could seize up next time you drive it. Don't take chances, replace faulty wheel bearings immediately.
On a 2005 dodge is there any possible way the hub where the lug nuts are could break off?
If the wheel bearing was bad enough, the hub could possibly come off. The wheel bearing would have to have been failed for a long time.
How long does it take to replace a wheel bearing hub in a 96 blazer?
With the proper tools and knowledge, 1 hour.
How long can you drive on bad wheel bearing?
If it truly is the wheel bearing that has gone bad, the noise will start out small then progressively get louder. On most modern cars the wheel bearing can be driven on until the noise is unbareable to the driver, I have driven a bad wheel bearing for a few hundred miles before having it replaced. Since the make, model, and year of the car is unknown a proper answer is unable to be provided so I am not suggesting to drive the car long distances but usually all that will happen is the noise will grow progressively worse.i would not drive at all you will cause dammage to spindle which will cost much more to repair and you could lose the entire wheel off the vehicle
What is the risk of driving a car with a bad wheel bearing?
The wheel bearing can overheat and fall apart causing the wheel to come off of the vehicle. This can happen with little to no warning. Have this repaired it is very dangerous to operate a vehicle with a bad wheel bearing.The bearing will usually make noise first then proceed to a vibration. If left long enough the bearing will either sieze or break apart, with the wheel coming off (but that last is an extreme case).I the worst case the wheel can seize up. Go get it fixed as soon as you can, if it is making a lot of noise and you have had it for a while you might even want to have the car brought in on a flatbed truck to the repair shop
How long can you drive before replacing a rear wheel bearing on a K1500 Chevy truck with about three-eighths inch of in out play?
Long enough for the bearing to sieze, wear the axle into, and cause you to have an accident. If it were my truck, I wouldn't drive it period, until this was repaired.
How long to change wheel bearing?
Depends on the vehicle, some can be changed in less than an hour, some take 2 -3 hours.
What kind of trailer can Chevy S-10 pull?
Utility trailers, landscaping trailers, camper trailers, all kinds of trailers as long as the don't exceed the trucks maximum towing weight. The maximum towing weight depends on the model (2 wheel or 4 wheel drive), engine, wheel base and GVW of the truck. Rule of thumb is that the trailer should not exceed the weight of the truck.
What is the best way to remove a front wheel bearing driver's side of a Toyota Rav all wheel drive without using a specialized tool?
a wrenchn with a short handle because he will not have to move it through a long distance
