0
How long does it take to replace a wheel bearing hub in a 96 blazer?
Wiki User
∙ 13y ago
With the proper tools and knowledge, 1 hour.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Wheel bearing seal for long chih trailer?
I used an SKF 30205J2/Q bearing and CR 692369 seal. Russ
How do you fix throw out bearing on 2000 Toyota Tacoma?
You replace it. As long as you have the transmission out, you might as well put the clutch and pressure plate in also.
Can you replace belt on 3.1 v6 without putting ac compressor back on?
Most of the time, there is no way to route the belt without all the pulleys in place. As long as the bearing in the clutch on the AC turns it is alright, the compressor itself does not need to work.
How do you repack front wheel bearings on a Toyota 4runner?
Pull the wheel front and rear bearing and clean out the old grease. You dont have to be perfect but do a good job. Then clean all the parts of as much of the old greas from the outside and make note of the order for the parts. Pull the seal and replace this part. Now all is clean and ready to re-grease. to pack the bearing you can do it old school or new school. Us old school will place a wad of grease in the palm of one hand and hold the bearing in the other. Then with a push and slide motion you can scrape the edge of the grease and shove it in one of the cracks of the bearins. This forcing motion will shove new grease in the bearing on one end. and the old grease out the other. When new grease is coming out the other end then turn the bearing and do the next ecction of the bearing. Its a long dirty process but it gets the job done. Do bother bearings and then put the parts back together in the back side of the hub. Prior to doing this put a good amount of grese on the bearing surfaces inside the hub. You don't have to plug it up but you dont want the new grease running out the bearing either. Then reinstall the seal and lube the shaft on the car. Reinstall the hub and then do the same thing on the front bearing. New school is the same except you use a bearing packer from a store. All the auto places and even wal mart will carry it. You place the bearing in a holder and use a grease gun to pack the bearing. It is time efficient and once you start to pump the grease you see the old come out the sides. Once all the old is out and new stuff starts coming out you are done. Nice and neat the first time but it uses a bit more grease that can go to waste. Just be careful. Since grease LOVES to hold dirt and debris you need to be super careful after you use it so it stays clean for next time. I just pulled my 96 Toyota bearings and the race and bearings look new. I change the grease about every 50 000 miles and I now have 325000 on the vehicle. So its worth the time.
How does one take offf a steering wheel on a 1982 Chevrolet TK model PK body style 12 ton with a 305 small block engine?
You will need a puller to remove the steering wheel, after you remove the nut and snap ring in the center of steering wheel. Ther are two holes in the wheel that are threaded. Install puller on center shaft, and screew 2 long bolts through the puller and into the holes on wheel.
How long does it take to replace the front wheel bearing on a 1998 Chevy Blazer?
If all goes well the job should take about an hour with proper tools and equipment. Keep in mind that if the hub/bearing assembly is rusted in, it could take longer.
How long does it take to replace a front wheel bearing on a 2007 Montana?
two minutes
What can happen if rear wheel bearing is not replaced?
If you do not change a bad wheel bearing the bearing will cut a groov in the axle.If it goes on long enough the axle will have to be replaced.It could also ruin the axle housing.Then you would have to replace the rearend.
How long will the wheel last with a damaged wheel bearing?
It could seize up next time you drive it. Don't take chances, replace faulty wheel bearings immediately.
Can you use a 97 S10 blazer transmission in a 98 S10 Blazer?
Yes you can, It's the same thing. As long as there both 2-wheel drives are 4-wheel drives.
Wheel bearing seal for long chih trailer?
I used an SKF 30205J2/Q bearing and CR 692369 seal. Russ
Can you plow snow with a 1991 Chevy s10 blazer?
Yes, as long as it has 4 wheel drive that works.
Is it safe to drive with a bad wheel bearing?
Not knowing how bad the bearing is, I can't say how long it will last before the wheel falls off. Drive to your local garage for repair and don't take the highway.
What is the warranty for a transmission on a 2002 Chevy blazer 4 wheel drive?
The factory warranty has long since expired.
Do you have to replace all 4 tires on a Chevy blazer if need to replace only 1 tire?
No, you can replace one tire as long as it is the exact same size as the rest of them.
If one wheel bearing is bad do you need to replace both?
No, but it is a good idea They usually wear out at about the same time, once you notice one is bad, it won't be too long before you notice the other one is bad.
Will a 1984 Chevy Blazer S-10 V6 2.81 transmission workin a 1987 Chevy Blazer S-10?
yes it will up to 93 as long as they are bothe 4wd or to wheel drive
