answersLogoWhite

0

The crank sensor is located beside starter, remove 2 starter bolts drop starter you will see it very easy took me 5 min the change mine, (maxamuscoal). P.s yes you have to remove starter there is no way around this.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

Gmc 2002 Yukon crankshaft position sensor location?

I have been having problems with finding the crankshaft sensor, what should i do or what can i do?


Where is the crankshaft sensor for a 1995 gmc jimmy?

The crankshaft sensor is by the crankshaft pullie (the balancer)


What sensor most likely will keep a 1999 gmc surburban from starting?

A common sensor that could prevent a 1999 GMC Suburban from starting is the crankshaft position sensor. This sensor monitors the position and rotational speed of the crankshaft, and if it fails, the engine control module may not receive the necessary information to start the engine. Other potential culprits include the camshaft position sensor and the fuel pump relay, but the crankshaft position sensor is a frequent issue for starting problems in this model.


Where is the crankshaft position sensor on a 1997 gmc Yukon?

front of engine, behind the harmonic balancer


Where is the crankshaft position sensor on 1994 GMC Sonoma 4.3 vin w?

Pretty sure it's at the front end of the crank.


Where is crankshaft position sensor located on 2000 gmc safari awd 4.3 engine?

Front, lower, passenger side of engine.


HOW REPLACE 2000 gmc sONOMA CRANKSHAFT POSITION SENSOR?

To replace the crankshaft position sensor on a 2000 GMC Sonoma, first disconnect the negative battery cable for safety. Locate the sensor, typically found near the crankshaft pulley at the bottom of the engine. Remove the electrical connector and the mounting bolt using a socket wrench, then pull out the old sensor. Install the new sensor by reversing the removal process, ensuring it is securely fastened and the connector is properly reattached, then reconnect the battery.


You have no spark or fuel injection spray on a 1993 GMC 5.7L?

check the CKP sensor (crankshaft position sensor). It is usually used for injector triggering on 90's GM vehicles.


Where is the crank shaft position sensor on a 1999 gmc safari van?

The CPS is located on the front of the engine attached to the harmonic balancer on the front of the crankshaft.


Where is the crankshaft position sensor located on a 2002 gmc sonoma?

On a 2002 GMC Sonoma, the crankshaft position sensor is typically located near the bottom of the engine, mounted on the engine block. It is often found close to the crankshaft pulley or flywheel, on the driver's side of the engine. To access it, you may need to remove some components, such as the air intake or other obstructive parts. Always refer to a service manual for specific details and guidance.


Where is the crankshaft sensor located on a 99 GMC Suburban 5.7?

On a 1999 GMC Suburban with a 5.7L engine, the crankshaft position sensor is typically located on the engine's lower front, near the crankshaft pulley. It is mounted near the oil pan on the driver's side and is accessible from underneath the vehicle. The sensor is usually held in place by a bolt and connected to the engine's wiring harness. Always refer to a repair manual for specific details and diagrams for your model.


Where is the crank shaft sensor located on a 1986 GMC Vandura 3500 with a 350 engine?

On a 1986 GMC Vandura 3500 with a 350 engine, the crankshaft position sensor is typically located near the bottom front of the engine, close to the crankshaft itself. However, it's important to note that models from this era may not have a crankshaft position sensor, as they often relied on mechanical systems for ignition timing. If your specific model does have one, check near the harmonic balancer or flywheel area for the sensor. Always consult the vehicle's service manual for precise location and specifications.