Some new wiper blades come with a clear plastic cover that protects the blade until you have installed it. Check to see if it is still on the blades.
remove complete wiper arn from vehicle so there is only the ribbed drive showing on the outside turn wipers on, then turn them off. this should put the drive at the return position.replace wiper arms with the arms in the home position.this should align them where they should be when turned off test to see if ya got em in right position
If you didn't fill the new filter up with clean diesel fuel when you assembled it, you introduced air into the system.
First make sure that this battery has a charge. Check its volts. Then if the battery is good, make sure the conectionns are clean. Then clean the connection to the starter relay ( solenoid ) just beside the battery. Then if needed, clean the conx. at the starter. If all the conx. are good, and still no start, jump the positive battery conx. at the starter relay to one of the small plug in conx. If the starter engages, then possible bad ign. switch. Hope something works. Good luck.
well my friend, your windshield wipers work off of an electric motor powered by your battery which is charged by the alternator, hope this makes sense to you, if wipers arent working it may be a fuse or the electric motor. if your alternator belt is not on or your alternator isn't working your battery will bo dead pretty quick and your car wont start at all. hope i helped sharris@maplenet.net if you have any car questions
Had same problem on my 1990 rs took it to two mechanics could not find issue. Its a fuse blade type kinda hidden where the battery goes its a black connector pop the top on it and replace fuse , it should run after that. Mine got fried when i gave someone a jumpstart.
Some people choose to do this to prevent the wipers from freezing to the car, and to make it easier to clean the windshield.I disagree 100% with these people. All this does it allow ice to collect all over the wipers, makeing them difficult to clean. The first thing I do when cleaning my car is to turn it on, full heat, with defroster on. I then clean the top/rest of my car. By the time I get to the windshield, the wiper area would be melted. I can then lift the wipers and clean the windshield, and my wiper blades do not have a spec of ice on them, so they wont streak all over the windshield. Try using your wipers after leaving them up, and the blades dont even touch the glass, ice does. Clean them off? You risk chipping the (rubber) blade, since its frozen and covered in ice.
i put a new windshield wiper moter in and the fuses are fine but my wipers still wont work
The back windshield wiper may not be working because there may be a short in the switch. It is best to have an auto mechanic look at it.
Your windshield wipers were most likely overloaded and blew the fuse, try replacing the fuse. If that does not fix it then it is possible that the wiper motor burned out and will require replacement.
If your wipers aren't working then check the grounding screw under the hood if it becomes loose your wipers wont work.
Just to bug the crap out of you. That is just the way they are. My 95 is the same. Just think happy thoughts when you look out of the windshield. Eventually you wont even notice them any more. Answer, I also have a wrangler 1991 that does that too. It stopped at the bottom to the windshield, until i replaced the windshield. then it started stopping up about 1/3 of the way. I believe that whatever tells the windshield wiper to stop got misaligned, but im too lazy to fix it.
Hi You need to check the fuse first if that's good its got to be either the switch od the motor do you hear any noise when you try ?a click ,moaning,grinding?
If the windshield wipers won't turn off on a 2000 Chevy Blazer, check the wiper relay switch. This is usually located in the engine compartment fuse box on top of the battery.
remove complete wiper arn from vehicle so there is only the ribbed drive showing on the outside turn wipers on, then turn them off. this should put the drive at the return position.replace wiper arms with the arms in the home position.this should align them where they should be when turned off test to see if ya got em in right position
check ground on wiper motor
A bad relay switch will cause the windshield wipers to not turn off. Replace the relay switch and the windshield wipers should turn off.
It is likely the Wiper Control module mounted to the wiper motor. I had this problem on my CTS and since found out other CTSs have also had the problem.