0
You might try fiber glass repair kit. It's important to wire brush all rust from the metal. After repairing you should use what's called rust converter on the metal which will seal it so no more damage from rust will occur.
What I did was added 4' x 10 ' piece of sheet metal available from a heating and air conditioning supply house. had to empty pool and remove top rails and inserted new metal and bolted sheet metal to pool wall. my old pool wall split. so was able to save pool all is great pool up and running I was told by a pool company that's been in business for over 30 years,that you can sand down the sides and get all the rust off,and then apply Duct Tape down the inside of the wall.I'm going to give it a try. I recently made this very repair without having seen this page. A neighbor recommended the "sheet metal" method as described above. I thought I'd get a little more specific in case it might be of assistance (My pool is aluminum 24' by 52" round and it is 13 years old). First, I had to drain the water at least down to the level of the lowest corrosion hole. Then, remove pool rails and peel back pool liner so that the hole is accessible from both sides.
Then, remove all rust from both sides of the pool wall with a wire brush or sandpaper. Wipe clean, and then spray with Rustoleum so that the rust will not return. Next, take your piece(s) of sheet metal and be sure that you have enough to cover all corrosion holes. For my repair, I had holes in a line from the skimmer and return down to the ground, but the sheet metal measured about one foot across so that I was more than covered. I also spray painted (clear) the sheet metal so that it wouldn't rust in case any moisture reached it. Then, apply a double layer of duct tape all the way around every edge of the sheet metal so that the edges and corners will not tear the liner. Line up the sheet metal so that it covers the holes, and duct tape it in place securely.
Next, check the liner for any holes that may be present. If there are holes in the walls of the pool, the water pressure may have pushed holes through the liner without the support in those spots. If there are any holes, they can be repaired with a vinyl pool liner repair kit (found at any pool store or online). That's about it. Now all you have to do is put the liner back, replace the rails and other hardware, and refill the pool. Check your chemical levels if you have to replace a lot of water.
What else can I help you with?
How to repair metal above ground pool walls?
I didn't know that there were swimming metal walls.
What are the best techniques for applying spackle to repair holes and cracks in walls?
The best techniques for applying spackle to repair holes and cracks in walls include cleaning the area, applying spackle with a putty knife, smoothing it out, letting it dry, sanding the surface, and then painting over it for a seamless finish.
What is the best method for using cement filler to repair holes in walls?
The best method for using cement filler to repair holes in walls is to clean the area around the hole, apply the filler with a putty knife, smooth it out, and let it dry completely before sanding and painting over it for a seamless finish.
What are the best techniques for applying drywall repair putty to fix holes and cracks in walls?
The best techniques for applying drywall repair putty to fix holes and cracks in walls are to clean the area, apply the putty with a putty knife, smooth it out evenly, let it dry completely, sand it down, and then paint over it for a seamless finish.
How can I effectively repair big holes in plaster walls?
To effectively repair big holes in plaster walls, you can follow these steps: Clean the area around the hole to remove any loose debris. Use a putty knife to apply a plaster patching compound to fill the hole. Smooth out the compound with the putty knife and let it dry completely. Sand the patched area to make it smooth and level with the rest of the wall. Apply a primer to the patched area before painting to ensure a seamless finish. By following these steps, you can effectively repair big holes in plaster walls.
How can I repair basement walls that are crumbling?
To repair crumbling basement walls, start by removing loose debris and cleaning the surface. Then, apply a waterproofing sealant or patching compound to fill in cracks and holes. Consider reinforcing the walls with steel mesh or carbon fiber strips for added strength. Finally, repaint or refinish the walls as needed for a finished look.
What are some common issues with mobile home walls and how can they be effectively repaired or maintained?
Common issues with mobile home walls include water damage, mold growth, cracks, and holes. To effectively repair and maintain them, it is important to address any water leaks promptly, repair cracks and holes with appropriate materials, and regularly inspect and maintain the walls to prevent further damage. Additionally, using moisture-resistant paint and sealants can help protect the walls from future issues.
What is the best method for applying exterior spackle to repair cracks and holes in the outer walls of a building?
The best method for applying exterior spackle to repair cracks and holes in the outer walls of a building is to first clean the area thoroughly, apply the spackle with a putty knife, smooth it out evenly, and allow it to dry completely before sanding and painting over it for a seamless finish.
How can I effectively use paste for wall holes to repair damaged walls?
To effectively use paste for wall holes to repair damaged walls, start by cleaning the area around the hole. Apply the paste generously to fill the hole, then smooth it out with a putty knife. Let it dry completely before sanding it down and painting over it to match the rest of the wall.
How can an operator repair pinhole leaks in the walls of a chlorine cylinder?
I suppose that the recommended solution is to send this cylinder to metal scrap.
What do you use to fill holes in walls?
Spackle or joint compound is commonly used to fill holes in walls.
How can I effectively repair holes in plaster walls?
To effectively repair holes in plaster walls, start by cleaning the area around the hole and removing any loose debris. Next, fill the hole with spackling compound or plaster patching compound, smoothing it out with a putty knife. Allow the compound to dry completely before sanding it down and painting over it to match the rest of the wall.
