0
The easiest way to reset a service lamp on any vehicle is to disconnect both battery terminals first. Run a wire across both battery terminals and leave attached for at least a couple of hours. Detach the wire and reconnect the battery terminals. Your service light should now be out.
Make sure that you do not run the wire across the positive and negative terminals of the battery. Make sure you disconnect both terminals and run the wire across the cables and not the actual battery terminals.
If your service engine light is on it means your computer is registering a code. Make sure you take your car to have it diagnosed properly instead of resetting the light. It may be a serious code that could cause problems in the future.
What else can I help you with?
How do you Fiat doblo service and oilchange light reset?
according to autodata service lamp can only be reset using suitable diagnostic computer Dr.Pedro VolksWagen service technician
Mb sprinter 311 cdi how do i reset service lamp on 311 Sprinter CDI?
what year or VIN no is your sprinter
Reset the service indicator lamp on opel combo?
with the switch off, press and hold the odometer button. Turn the switch on, and the odometer will be in insp mode. mode. Press the odometer button until the indicator shows --- . Turn the switch off and the lamp should be reset.
How do you reset the service to the next service?
how to reset service to next service
How do you reset lamp hours on a Toshiba TLP-XD2000?
To reset the lamp hours on a Toshiba TLP-XD2000 projector, first ensure the projector is powered on. Navigate to the "Lamp" menu using the remote or the projector's control panel, then select the option to reset the lamp hours. Confirm the reset when prompted, and the lamp hour counter will be set back to zero. Be sure to check the user manual for specific button sequences, as they may vary.
How do you reset the oil change lamp on a 2007 town and country?
To reset the oil change lamp on a 2007 Town and Country, locate the reset button on the instrument panel. Hold the button down for 5 seconds.
How can you reset your maintenance reminder light on your 1995 Ram 3500?
The SRI lamp may only be reset with the use of a DRBII scan tool, or equivalent. If this is not available, you will have to take the vehicle to a properly equipped shop for them to reset the lamp.
How do you reset the service light on an Opel Corsa 2005 1.6 Sport?
There's no great ''trade secret'' as to how to reset the service indicator lamp on most Vauxhall's, simply refer to pages in the Owner's Handbook! For reference of those interested in such matters, but who might not have access to an owner's manual, this is the procedure to follow: Vauxhall service reset * Turn Ignition Off * Hold Trip Reset In * Turn Ignition On Still Holding * Trip Reset wait for three dashes * Turn off Ignition * Turn on Ignition to confirm To the best of my knowledge, the above service light reset procedure applicable to most Vauxhalls HOPE THIS SAVES YOU PAYING FOR INFORMATION!!!!!!!!!!!!!!!!!!!! ;-)
Why doesnt brake lamp failure lamp on dash of 94 Honda Accord not reset after bulb replacement?
Remove the negative battery terminal (-) for about 15 minutes and most codes will reset.
How do you reset service indicator on2009 jaguar xf?
> Resetting service reminder: 1. Press and hold rear fog lamp switch 2. Turn ignition on, do not start engine 3. Release rear fog lamp switch 4. Press and hold trip button (end of left side stalk) 5. Press and hold rear fog lamp switch 6. See "Resetting Service Light" message in message center
How do you reset a engine warning lamp on a Hino 500 series truck?
To reset the engine warning lamp on a Hino 500 series truck, first, ensure that the underlying issue causing the warning has been resolved. Then, use a diagnostic scan tool to clear the fault codes stored in the engine control unit (ECU). If a scan tool is not available, disconnect the truck's battery for about 10-15 minutes, which may also reset the lamp. Always consult the vehicle's service manual for specific procedures and precautions.
How do you reset the lamp hours after you change the bulb?
To reset the lamp hours after changing the bulb, locate the reset option in the projector or device's menu. This is often found under settings, maintenance, or lamp settings. Use the remote control or on-device buttons to select the reset option, then confirm the action. Refer to the user manual for specific instructions related to your model, as the process may vary.
