0
How do you disassemble polaris rear drive shafts on 2002 sportsman 500 HO Need to change inner CV boots?
The previous answer is not correct.
There is a ring but it is not accessable. You just jerk on the axel to remove it.
This is usually nearly impossible.
I have used small wedges between the tranny housing and the axel but don't really reccomend this as damage may occur.
The book says something like a sharp jerk as with a dent puller but if the end is dry and or corroded this is not easy. Lots of penetrating oil will help.
Like I said, there is a ring also but it is of the expansion type and is supposed to keep the axel in but can be pulled out. A stick in the woods did just that on mine.
There should be a retainer ring that you can spread apart. Then just tap the housing with a mallett and it should start to come off.
would like to know how to remove inner splin in housing
What else can I help you with?
Grease points on 2004 Polaris Sportsman 500 ATP HO?
On a 2004 Polaris Sportsman 500 ATP HO, you should grease the front and rear suspension components, steering components, and drive shafts. Use a high-quality lithium grease and follow the recommended intervals in the owner's manual for regular maintenance. Make sure to clean and inspect the components before greasing to ensure proper lubrication.
What is required to change a 4l60 transmission 2wd to 4wd?
The center shafts in all 4x4 transmission are longer then the shafts in a 2WD trans. Does not matter what kind of transmission it is. To change the center shafts you have to take trans. all the way apart.
How do you disassemble rear end on Arctic Cat 650 4-wheeler 4x4?
To disassemble the rear end of an Arctic Cat 650 4-wheeler 4x4, start by safely lifting the vehicle and removing the rear wheels. Next, disconnect the rear differential by unbolting the mounting brackets and any associated drive shafts or links. Remove the axle shafts and then detach the rear differential from the frame. Be sure to keep track of all hardware and components for reassembly.
93 to 92 Saturn engine change?
No this will not work. Crank shafts are different
What things have an universal joint in it?
Drive shafts, PTO shafts, Steering shafts, Axle shafts,
Where ar barbules and pinnae connected to the feather of birds?
shafts Barbules and pinnae are connected at the shafts of the feathers. This is on a bird.
How do you remove the rear axle on a 2000 Polaris Trail Boss?
buy the clymer manual first. there are clips on the inside of the cups remove them press the Ujoint out of the yoke. someone told me you need to install the rear drive shafts with the yokes/u joints the same on both sides lined up. Mine were from the factory. thanks
What joint allows connected shafts to spin freely while permitting a change in direction?
universal joint
Explain how to check the ratios of a gearbox?
The input and output shafts need to be marked Then put in a particular gear Rotate the input shaft ten revolutions and count the output shaft revolutions. Or read the specs in the manual OR disassemble the trans and count the gear teeth.
What are the different types of bike shafts available for purchase?
The different types of bike shafts available for purchase include solid shafts, hollow shafts, and splined shafts. Solid shafts are one continuous piece of metal, while hollow shafts have a hollow center. Splined shafts have grooves that fit with corresponding grooves on other bike components. Each type of shaft has its own advantages and is used for different purposes in biking.
Do graphite shafts stiffen or become more flexible with age?
Graphite shafts are very durable and will last for many years without a change in performance. They will however weaken with extended use. Make sure you keep good care of them.
What can be done to fit 2007 wheels on a 2001 jeep wrangler?
you'd have to change your axle shafts, different bolt pattern.
