0
What else can I help you with?
Renault 5 1981 exhaust manifold is it the same as the turbo engine?
NO.
How do you tel witch is inlet and exhaust Renault scenic?
The exhaust manifold will have an exhaust pipe attatched! The exhaust manifold for example on a scenic 1.6 petrol, is located at the front of the engine block and have a heat shield attatched.
Does a cracked manifold in a Renault Megane affect emissions?
If you are referring to the exhaust manifold then it should not affect emissions as the o2 sensor is after the exhaust blow it will adjust emmissions accordingly
How do you change the exhaust manifold gasket on a 93 Chevy astro van?
You will need to remove the exhaust manifold retaining bolts in your 1993 Chevy Astro. Remove the exhaust manifold. Remove the exhaust manifold gasket and clean the surface. Reverse the process to install the new exhaust manifold gasket.
How do you change exhaust on 1996 Renault laguna?
To change the exhaust on a 1996 Renault Laguna, start by safely raising the vehicle and securing it on jack stands. Remove the old exhaust by loosening the clamps and bolts connecting it to the manifold and the rubber hangers. Install the new exhaust by reversing the removal process, ensuring all connections are tight and secure. Finally, check for leaks by starting the engine and inspecting the exhaust system.
Where is the starter motor on a Renault kangoo?
On the diesel 1.9 it`s below the exhaust manifold. Best seeing it from underneath.
How do you check oil an water on Renault clio 2000 1.4 petrol?
you need to be double jointed its below the exhaust manifold
What is Chevy 454 exhaust manifold bolt torque install sequence?
40 lbs
How do you replace exhaust manifold gaskets on ford expedition?
Exhaust Manifold Removal & Installation 4.6L, 5.4L and 6.8L Engines 1. Raise and safely support the vehicle. 2. Remove the front fender splash shield. 3. For the left-hand exhaust manifold, remove the EGR valve-to-exhaust manifold tube and disconnect the Differential Pressure Feedback Exhaust [DPFE] gas recirculation transducer hoses. 4. Remove the oil stick from the engine. 5. On the 4.6L and 5.4L engines, remove the catalytic converter-to-exhaust manifold bolts. On the 6.8L engine, remove the front exhaust pipe from the manifold. 6. Remove the exhaust manifold mounting nuts, then remove the exhaust manifold itself. 7. Remove and discard the old gasket. 8. Clean and inspect the exhaust manifold for damage. To install: 9. Position a new gasket and the exhaust manifold onto the engine block. 10. Install the mounting nuts and tighten, in the sequence shown, to 13-16 ft.lbs. [18-22 Nm] on the 4.6L and 5.4L engines. Tighten the nuts to 17-20 ft.lbs. [23-27 Nm] on the 6.8L engine. {Tighten the passenger side exhaust manifold bolts in the order shown-4.6L and 5.4L engines} Kriss x kross 11. On the 6.8L engine, tighten the exhaust manifold-to-front pipe fasteners to 27-34 ft.lbs. [34-46 Nm]. 12. On the 4.6L and 5.4L engines, attach the catalytic converter to the exhaust manifold, then install the catalytic converter-to-exhaust manifold bolts and tighten to 25-34 ft. lbs. [34-46 Nm]. 13. Install the oil stick. 14. For the left-hand exhaust manifold, install the PDFE transducer hoses if equipped, and EGR-to-exhaust manifold tube. Tighten the upper and lower fitting to 26-33 lbs. [35-45 Nm]. 15. Install the front fender splash shield. 16. Lower the vehicle to the ground.
1996 Nissan Pathfinder change exhaust manifold?
What engine???????? You should refer to repair manual if not familiar with auto repair and understand the terminology before attempting Remove nuts holding exhaust manifold to cylinder head & remove nuts/bolts holding exhaust manifold to exhaust pipes Use new exhaust manifold gaskets and install the new manifold securing the manifold to cylinder head (may need to but new nuts and or bolts) by "snugly" tightening manifold to cylinder head if not refering to repair manual
How do you replace exhaust manifold gasket ford 4.9 F 150 1996?
Exhaust Manifold Removal & Installation 4.6L, 5.4L and 6.8L Engines 1. Raise and safely support the vehicle. 2. Remove the front fender splash shield. 3. For the left-hand exhaust manifold, remove the EGR valve-to-exhaust manifold tube and disconnect the Differential Pressure Feedback Exhaust [DPFE] gas recirculation transducer hoses. 4. Remove the oil stick from the engine. 5. On the 4.6L and 5.4L engines, remove the catalytic converter-to-exhaust manifold bolts. On the 6.8L engine, remove the front exhaust pipe from the manifold. 6. Remove the exhaust manifold mounting nuts, then remove the exhaust manifold itself. 7. Remove and discard the old gasket. 8. Clean and inspect the exhaust manifold for damage. To install: 9. Position a new gasket and the exhaust manifold onto the engine block. 10. Install the mounting nuts and tighten, in the sequence shown, to 13-16 ft.lbs. [18-22 Nm] on the 4.6L and 5.4L engines. Tighten the nuts to 17-20 ft.lbs. [23-27 Nm] on the 6.8L engine. {Tighten the passenger side exhaust manifold bolts in the order shown-4.6L and 5.4L engines} Kriss x kross 11. On the 6.8L engine, tighten the exhaust manifold-to-front pipe fasteners to 27-34 ft.lbs. [34-46 Nm]. 12. On the 4.6L and 5.4L engines, attach the catalytic converter to the exhaust manifold, then install the catalytic converter-to-exhaust manifold bolts and tighten to 25-34 ft. lbs. [34-46 Nm]. 13. Install the oil stick. 14. For the left-hand exhaust manifold, install the PDFE transducer hoses if equipped, and EGR-to-exhaust manifold tube. Tighten the upper and lower fitting to 26-33 lbs. [35-45 Nm]. 15. Install the front fender splash shield. 16. Lower the vehicle to the ground.
How do you change exhaust manifold Mitsubishi mirage?
To change the exhaust manifold on a Mitsubishi Mirage, first, ensure the engine is cool and disconnect the battery. Remove any components obstructing access, such as the intake manifold or heat shield. Unbolt the exhaust manifold from the engine block and disconnect the exhaust pipes, taking care to replace any gaskets. Finally, install the new manifold in reverse order, ensuring all bolts are tightened to the manufacturer's specifications.
