answersLogoWhite

0

Remove the deck. First by pulling the pins that attach the lift brackets, and then remove the rear spring, and the 2 belt guides under the engine for the belt that drives the deck (1/4" socket). After the deck is out, release the spring that applies tention on the right idler pulley (you'll have to remove the 2 side pulley covers).

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

How do you replace mower deck belt on Huskee LT 4200 Riding Mower?

To replace the mower deck belt on a Huskee LT 4200 riding mower, first ensure the mower is turned off and safely positioned. Remove the deck by disconnecting the lift lever and any retaining pins or bolts. Once the deck is off, locate the old belt, remove it from the pulleys, and then install the new belt by following the path indicated in the owner's manual. Finally, reattach the deck and ensure everything is secured before testing the mower.


How do you change the motion drive belt on a Huskee 42 riding mower?

To change the motion drive belt on a Huskee 42 riding mower, first, ensure the mower is turned off and the key is removed. Raise the mower deck and remove the belt covers to access the old belt. Take note of the belt routing, then remove the old belt from the pulleys and replace it with the new one, ensuring it follows the same path. Finally, reassemble the covers and lower the deck before testing the mower.


How do you put deck belt on huskee lt 4200 lawn mower?

Changing the deck belt on the Huskee IT4200 lawn mower involves working around the spring and 2 belt drive guides in the motor area. Properly loading the spring before the guides is the secret to success.


How do you install drive belt on husky 46inch deck?

To install the drive belt on a Husky 46-inch deck, first, raise the deck and remove any necessary covers to access the belt. Next, carefully route the new belt around the pulleys according to the diagram usually found on the deck or in the owner's manual. Ensure the belt is seated properly in the grooves, then reassemble any covers and lower the deck. Finally, check the belt tension and alignment before testing the mower.


Where do you find a diagram for a huskee 50 mower?

If you mean the deck belt of a 50" deck, then try the related link at one of my sites under MTD decks.


how to install main drive belt on Murray riding mower?

To install the main drive belt on a Murray riding mower, first ensure the mower is turned off and the key is removed for safety. Remove the mower deck by disconnecting the belt and any necessary bolts. Next, route the new drive belt around the engine pulley and axle pulley, following the mower's belt routing diagram, which is usually found on the mower's frame. Finally, reattach the deck and check the tension on the belt before starting the mower.


How do you remove rear drive pulley on Huskee riding lawn mower with it on mower?

To remove the rear drive pulley from a Huskee riding lawn mower while it's still on the mower, first ensure the mower is turned off and the battery is disconnected for safety. Remove the belt from the pulley by loosening the tensioner if necessary. Then, use a socket wrench to remove the bolts securing the pulley to the shaft. If the pulley is stuck, gently tap it with a rubber mallet to help loosen it.


MTD Mower 42 deck how to install the deck belt?

you were no help


Belt diagram for a huskee 46 24hp lawn tractor?

Is there a diagram for belt replacement on a 46" 24h.p. Huskee lawn tractor


How do you install a belt on a L1742 Scott's lawn tractor?

what is the belt diagram for a scotts lawn mower s1742


How do you install a 54 inch lawn mower belt for white tractor?

To install a 54-inch lawn mower belt on a White tractor, first, ensure the mower is turned off and disconnected from any power source. Remove the mower deck by detaching the necessary pins and brackets. Then, route the new belt around the pulleys according to the diagram typically found on the mower, making sure it sits properly in the grooves. Finally, reattach the mower deck and double-check that the belt is tensioned correctly before operating the mower.


How do you install belt on ls45 mower?

To install the belt on an LS45 mower, first, ensure the mower is turned off and the spark plug is disconnected for safety. Remove any protective covers to access the belt area, then carefully thread the new belt around the pulleys according to the manufacturer's diagram. Ensure the belt is properly aligned and seated in the grooves. Finally, reattach any covers and reconnect the spark plug before testing the mower.