0
To remove the rear drive pulley from a Huskee riding lawn mower while it's still on the mower, first ensure the mower is turned off and the battery is disconnected for safety. Remove the belt from the pulley by loosening the tensioner if necessary. Then, use a socket wrench to remove the bolts securing the pulley to the shaft. If the pulley is stuck, gently tap it with a rubber mallet to help loosen it.
What else can I help you with?
How do you remove the drive pulley off the shaft of a GT262 riding mower?
Use a puller so you do not bend the pulley.
How do you tighten a drive belt on Lowes MTD Riding Tractor?
remove the varable speed pulley-replace both belts re-install varable speed pulley--your done.
How do you change the motion drive belt on a Huskee 42 riding mower?
To change the motion drive belt on a Huskee 42 riding mower, first, ensure the mower is turned off and the key is removed. Raise the mower deck and remove the belt covers to access the old belt. Take note of the belt routing, then remove the old belt from the pulleys and replace it with the new one, ensuring it follows the same path. Finally, reassemble the covers and lower the deck before testing the mower.
How to change an alternator in a 3126 cat engine?
remove the old one, remove the drive pulley. install the drive pulley on the new alternator,lock the shaft with an allen or drill bit thru the housing hole,torq the drive pulley nut, install it like the old one was installed.
How do you replace the drive belt on a 16.5hp 42 inch deck on a huskee riding mower?
There are lots of mounting points on the deck. Pay attention to how they are taken off. 1. Remove the deck, by "rolling" the belt offf of the engine crankshaft pulley 2. Remove all the hold-down cotter pins (there should be 8), displace the deck from the 8 hangers, remove the deck from beneath the mower 3. Lift the mower to an upright position and secure (so it doesn't fall on you) 4. Remove the engine crankshft pulley, along with that end of the belt, by removing the crankshaft bolt (pay attention to how it comes off) 5. Unscrew the "Forward/ Reverse" knob, remove the plate beneath the knob to give access to the PTO pulley. (be sure to unplug the SAFETY device from the bottom of plate) 6. Remove the SNAP RING from the PTO pulley, and remove the pulley (pay attention how it comes off. Which belt where? MY pulley was a double pulley, of which one side "Floated") 7. Remove the clip (spring) from the Forward/ Reverse lever that is about half way down the shaft, and to the left of the pulley. Give it a twist and squeeze to the right. (This is tricky to put back on. PAY ATTENTION. The "U" part of the clip will go on the BACK side of the shaft when reinstalling. Then use pliers and/ or screwdriver to push the other part over the front side to catch the shaft) 8. Pull the tension pulley away and remove the rear drive belt. GREASE ALL BEARINGS BEFORE PUTTING THE MOWER BACK TOGETHER!
How do you change drive belt on mtd riding mower mod 13ax675g062 ser 1d309c30054?
which one? there are two belts. take off the shift knob and access panel (two screws) remove clip on the varispeed pulley and pull up and remove the top belt which is the rear one and then you can also remove the bottom belt which is the front one, then to remove front belt you will have to first remove deck belt at the engine pulley and then remove the pulley to drop it down so you can remove the front drive belt. the installation is the reverse. the rear belt is kinda harder to install, just get it started on the rear pulley and walk it on, it is sometimes easier to remove the battery and the insert to get at it better. sometimes you will have to do some adjustments but not always. Get the manual somewhere on the web which will tell how to change belt and adjust as necessary.
WHAT PULLEY DO I loosen to get single drive belt on?
If you are referring to the Serpentine belt, you loosen no pulley. You simply remove tension from the belt. The tension is applied by the Idler Pulley. Pry the idler back and remove the belt.If you are referring to the Serpentine belt, you loosen no pulley. You simply remove tension from the belt. The tension is applied by the Idler Pulley. Pry the idler back and remove the belt.
how to install main drive belt on Murray riding mower?
To install the main drive belt on a Murray riding mower, first ensure the mower is turned off and the key is removed for safety. Remove the mower deck by disconnecting the belt and any necessary bolts. Next, route the new drive belt around the engine pulley and axle pulley, following the mower's belt routing diagram, which is usually found on the mower's frame. Finally, reattach the deck and check the tension on the belt before starting the mower.
How do you remove a wrx power steering pump?
Undo the hoses remove drive belts from pulleys undo pulley bolt and remove pulley no special tool needed should slide off remove bolts at front of pump remove pump
How do you remove the power steering pulley from a 2002 Chevy Suburban w 4 wheel drive?
This requires a special tool to remove and install the pulley. Most auto parts stores should have one in stock Best to remove the pulley with the pump removed from the engine compartment.
How do you change the belt on a ranch king riding lawn mower?
You can change the drive belt, on your lawnmower, by loosening the tensioner pulley. With the tensioner pulley, loosen the drive belt will come off and can be replaced.
Where is a tensioner pulley on a 1981 Oldsmobile omega?
When looking at the engine from the front, the tension pulley is the only wheel on the drive belt that has the belt on the inside of it. All of the other pulleys have the belt going around the top of the pulley. The tension pulley has a bolt that can be loosened and then tightened to remove the drive belt.
