0
What else can I help you with?
How do you tighten a drive belt on Lowes MTD Riding Tractor?
remove the varable speed pulley-replace both belts re-install varable speed pulley--your done.
How to change an alternator in a 3126 cat engine?
remove the old one, remove the drive pulley. install the drive pulley on the new alternator,lock the shaft with an allen or drill bit thru the housing hole,torq the drive pulley nut, install it like the old one was installed.
WHAT PULLEY DO I loosen to get single drive belt on?
If you are referring to the Serpentine belt, you loosen no pulley. You simply remove tension from the belt. The tension is applied by the Idler Pulley. Pry the idler back and remove the belt.If you are referring to the Serpentine belt, you loosen no pulley. You simply remove tension from the belt. The tension is applied by the Idler Pulley. Pry the idler back and remove the belt.
How do you change drive belt on mtd riding mower mod 13ax675g062 ser 1d309c30054?
which one? there are two belts. take off the shift knob and access panel (two screws) remove clip on the varispeed pulley and pull up and remove the top belt which is the rear one and then you can also remove the bottom belt which is the front one, then to remove front belt you will have to first remove deck belt at the engine pulley and then remove the pulley to drop it down so you can remove the front drive belt. the installation is the reverse. the rear belt is kinda harder to install, just get it started on the rear pulley and walk it on, it is sometimes easier to remove the battery and the insert to get at it better. sometimes you will have to do some adjustments but not always. Get the manual somewhere on the web which will tell how to change belt and adjust as necessary.
How do you remove a wrx power steering pump?
Undo the hoses remove drive belts from pulleys undo pulley bolt and remove pulley no special tool needed should slide off remove bolts at front of pump remove pump
how to install main drive belt on Murray riding mower?
To install the main drive belt on a Murray riding mower, first ensure the mower is turned off and the key is removed for safety. Remove the mower deck by disconnecting the belt and any necessary bolts. Next, route the new drive belt around the engine pulley and axle pulley, following the mower's belt routing diagram, which is usually found on the mower's frame. Finally, reattach the deck and check the tension on the belt before starting the mower.
How do you remove the power steering pulley from a 2002 Chevy Suburban w 4 wheel drive?
This requires a special tool to remove and install the pulley. Most auto parts stores should have one in stock Best to remove the pulley with the pump removed from the engine compartment.
Where is a tensioner pulley on a 1981 Oldsmobile omega?
When looking at the engine from the front, the tension pulley is the only wheel on the drive belt that has the belt on the inside of it. All of the other pulleys have the belt going around the top of the pulley. The tension pulley has a bolt that can be loosened and then tightened to remove the drive belt.
How do you remove power steering pulley from 1998 Buick Lesabre?
To remove the power steering pulley from a 1998 Buick LeSabre, first, disconnect the negative battery cable and remove the drive belt from the pulley. Use a pulley puller tool to carefully extract the pulley from the power steering pump shaft, ensuring you follow the tool's instructions for proper use. Once the pulley is removed, inspect the pump and pulley for any signs of wear before reinstalling or replacing them as necessary. Remember to reattach the drive belt and reconnect the battery once the job is complete.
How do you change the belt on a ranch king riding lawn mower?
You can change the drive belt, on your lawnmower, by loosening the tensioner pulley. With the tensioner pulley, loosen the drive belt will come off and can be replaced.
How do you replace the drive and variable speed belts on MTD 14AZ808K131?
Set the parking brake and disconnect the spark plug wire. Remove the cutting deck and the battery. Loosen the pulley and remove the upper belt. Remove the belt guide and the belt keeper. Loosen the bolt on the crankshaft pulley. Remove the lower drive belt.
What if there is smoke coming from the drive belt area at the left of the engine of a 97 mercury sable but it is not the belt?
remove drive belt and check all pulley wheels for freedom of movement sounds like a pulley wheel is bad, probably the belt tensioner pulley
