answersLogoWhite

0

You release the spring tension on the tensioner, a pulley in the belt system who's only purpose is to keep the belt tight. Normally you can use a ratchet to move the pulley away from the belt, but some are adjustable and require loosening a bolt.

User Avatar

Wiki User

10y ago

What else can I help you with?

Related Questions

How do you change the drive belts in a Nissan 350Z?

To change the drive belts in a Nissan 350Z, first ensure the engine is off and cool. Remove the engine cover, then locate the alternator and power steering belts, loosening the tensioner bolts to relieve tension. Slide the old belts off and replace them with new ones, making sure they are properly aligned on the pulleys. Finally, re-tension the belts, secure the tensioner bolts, and replace the engine cover.


How do you replace the drive belts on an 1974 Mercedes sl?

how do you replace the drive belts on an 1974 mercedes 230


How to replace drive belts in Mercedes 420sel?

To replace the drive belts in a Mercedes 420SEL, first, ensure the engine is cool and disconnect the battery. Loosen the tensioner pulley to relieve tension on the belts, then remove the old belts by sliding them off the pulleys. Install the new belts by routing them according to the belt diagram typically found under the hood, and then adjust the tensioner to ensure proper tightness. Finally, reconnect the battery and start the engine to check for proper operation.


How do you replace upper and lower drive belts on mtd 13aj688h131?

To replace the upper and lower drive belts on an MTD 13AJ688H131, first, disconnect the spark plug for safety. Remove the mower deck and any necessary covers to access the belts. Take note of the belt routing, then remove the old belts by releasing the tension and sliding them off the pulleys. Install the new belts by following the same routing, ensuring they are properly seated, and reassemble the mower before reconnecting the spark plug.


What does a belt tensioner do on an engine?

It keeps drive belts under tension (pulled tight)


Is a serpentine belt and drive belt one in the same?

Technically,Yes. But realistically no. They are both drive belts, but the term drive belt is normally what is referred to as a non-serpentine belt. This term is used to distinguish between the two type belts. A drive belt tension must be adjusted manually, whereas a serpentine belt tension is controlled by a tensioner.


Why is there a squeal when you drive your sonata through puddles?

The squeeling if from the belts, this can be normal but you should check the belts to see if they are worn or cracked. Also check the tension this can be a problem aswell.


Why would an automatic car make a short squeak noise while shifting between 3rd and 4th gears while accelerating hard?

This sounds like you have a loose or worn drive belt. Check all the belts and their tension.This sounds like you have a loose or worn drive belt. Check all the belts and their tension.


How do you release the tension to replace serpentine belt on Mazda?

Most likely there is a spring loaded device called a belt tensioner. There is a pulley on it with a bolt or square inset in it. sometime a socket or 3/8" drive extention can be used to move the pulley and release the tension on the belt.


How do you replace the Power Steering Pump on a 1999 Altima Will you have to remove anything other than the drive belts?

very carefully


How do you replace a tensioner pulley on a 1997 Chevy Lumina?

use a 3/8 drive ratchet to loosen the tension and take your belt off.Then unbolt the center bolt of the tension assembly and replace with a new unit.


How do you replace the drive belt on a Kubota t1670 lawn tractor?

To replace the drive belt on a Kubota T1670 lawn tractor, first, ensure the tractor is on a flat surface and the engine is off. Remove the mower deck by disconnecting the necessary pins and belts, then locate the old drive belt on the engine and transmission pulleys. Slide the old belt off and replace it with the new one by threading it around the pulleys in the correct path. Finally, reassemble the mower deck and test the new belt to ensure proper tension and function.