answersLogoWhite

0

lower the deck all the way down. at the rear of the deck you will see a plastic wingnut on either side. remove blades using vice grips to loosen the bolt. you will needto use a shop rag with your free hand to hold the blade in place so you dont cut yourself. next remove wingnuts in rear. there is a bar in the front-most part of the deck held in place with a cotterpin. remove pin to remove bar. depending on your model of mower, that should be it. if not look at the deck frame for any other nuts or bolts.

User Avatar

Wiki User

18y ago

What else can I help you with?

Related Questions

How to install a belt for a 42'' Murray mowing deck?

To install a belt on a 42'' Murray mowing deck, first, ensure the mower is turned off and disconnected from the power source. Remove the deck from the mower by detaching the pins or bolts securing it. Once the deck is removed, locate the old belt and note its routing; then, remove it from the pulleys. Install the new belt by following the same path as the old one, ensuring it sits properly in the pulleys, and reassemble the deck back onto the mower.


How do you attach the mower deck to your Murray Garden Tractor?

reinstalling after blade exchange


how to install main drive belt on Murray riding mower?

To install the main drive belt on a Murray riding mower, first ensure the mower is turned off and the key is removed for safety. Remove the mower deck by disconnecting the belt and any necessary bolts. Next, route the new drive belt around the engine pulley and axle pulley, following the mower's belt routing diagram, which is usually found on the mower's frame. Finally, reattach the deck and check the tension on the belt before starting the mower.


How do you change the drive belt on a Murray lawn mower model 13an772s058?

To change the drive belt on a Murray lawn mower model 13AN772S058, first, ensure the mower is turned off and disconnect the spark plug for safety. Remove the mower deck by taking off the retaining clips or bolts. Once the deck is removed, locate the drive belt routing and carefully slide the old belt off the pulleys. Install the new belt by following the same routing, and reassemble the deck before reconnecting the spark plug.


How do i Change belt for blades Murray riding mower model 40907X20A?

I changed the blade belt on my Murray mower. Now one blade stops and goes. If I lower the deck the blade stop . What did I do wrong?


Where are the kill switches on a Murray 14.5 hp 40 riding mower?

There is a yellow wire under the seat on my 14.5 HP Murray 42'' deck mower, and plug it in or don't that's where all killswitches are on a Murray lawnmower and pretty sure they still are today.


How do you remove a deck belt from a white riding lawn mower?

It depends on the mower. Some you will need to remove the deck. Some you will have to remove the deck mounting brackets. Others will change without removing anything. For detailed info please ask again with the make and model of the mower.


Cub cadet deck removal?

How do you remove the deck from the cub cadet lt1046 mower? The instructions do not say how to remove the cable and springs that are attached to the deck.


How many blades does a 38 inch deck for a Murray riding mower have?

most likely 2, look underneath


Need a use Murray riding lawn mower deck?

That depends on what state you are in. I'm in FL and have a 42" for sale


What size blade belt for a 40 inch deck 12.5 engine Murray rideing mower?

84 inch


How do you replace mower deck belt on Huskee LT 4200 Riding Mower?

To replace the mower deck belt on a Huskee LT 4200 riding mower, first ensure the mower is turned off and safely positioned. Remove the deck by disconnecting the lift lever and any retaining pins or bolts. Once the deck is off, locate the old belt, remove it from the pulleys, and then install the new belt by following the path indicated in the owner's manual. Finally, reattach the deck and ensure everything is secured before testing the mower.