answersLogoWhite

0

After removing the pinion nut, a 2 jaw puller should do the trick.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How do you replace the pinion shaft seal on your F-350 dually?

to replace pinion shaft seal you need to drop the drive shaft from the rear end then with large socket remove pinion nut from front of yoke remove yoke remove old pinion seal install new pinion seal reinstall yoke and pinion nut to specified torque re install drive shaft note now is the time to check and see if U-joints need replacing


How do you replace the pinion shaft seal on your F 350 dually?

to replace pinion shaft seal you need to drop the drive shaft from the rear end then with large socket remove pinion nut from front of yoke remove yoke remove old pinion seal install new pinion seal reinstall yoke and pinion nut to specified torque re install drive shaft note now is the time to check and see if U-joints need replacing


How do you replace a pinion seal?

Remove driveshaft,remove pinion nut that holds the driveshaft yoke on. Then remove the yoke and the seal will be behind the yoke.To pull the seal you need a seal puller or you could use a couple of screwdrivers to pry it out of the axle housing. Install seal & asm in reverse order.


How do you replace pinion seal 1995 jeep Cherokee?

remove drive shaft. remove large nut on pinion . using a puller, remove yoke from pinion.remove pinion seal. install new pinion seal.replace yoke. install NEW pinion nut,to correct torque specs. reinstall drive shaft.PS now is a good time to replace U-joints while u have drive shaft out


How do you replace the pinion bearing and seal on a 02 mountianieer?

to replace pinion bearing and seal you need to remove drive shaft.you then remove the pinion nut from pinion shaft. u usually need a pretty good rattle gun to remove this .then remove yoke from front of differential.u may need a puller but usuall tapping with hammer will loosen it. remove the bearing and replace with new one then install seal and replace cover and ypke. replace pinion nut, fill with oil.replace drive shaft


How do you fix leaking rear axle on 2001 ford expedition?

Pinion seal: Remove the drive shaft from the yoke. Pull the pinion yoke off the pinion shaft. Remove the old seal and hammer on a new one. Seal is about 10 bucks. Re-assemble Rear cover: Remove the cover bolts. Put a pan under the rear end and pry the cover off. Clean and re-silicone the cover Re-assemble. WARNING!!!!! Don't let the rear end run dry, will cost you pinion bearings in a very short time.


How do you change rear pinion bearing on a 2004 dodge 1500 ram 4x4?

1. remove rear drive shaft.2.remove diff.cover.3.remove both axles.4.remove carrier case assy.5.remove drive shaft yoke.6.tap pinion gear out of housing with (brass hammer).7 remove pinion seal and front pinion bearing.8.rear pinion bearing well need pressed off & on the pinion gear.9.you need to use a punch drive the bearing race from housing both.


How do you replace rear pinion seal on a 2005 dodge ram 2500 diesel?

To replace the rear pinion seal on a 2005 Dodge Ram 2500 Diesel, first, safely lift the vehicle and support it on jack stands. Remove the driveshaft by unbolting it from the rear differential and marking its position for reinstallation. Next, use a socket to remove the pinion nut and pull the yoke off, exposing the old seal. Carefully pry out the old seal, install the new seal, reassemble the yoke, and tighten the pinion nut to the manufacturer's specifications before reattaching the driveshaft.


How do you replaced and adjust your rear pinion bearing on your 1995 ford full size bronco?

chock wheels on vehicle u will need a good heavy duty air gun or a good solid socket with breaker bar now get under vehicle, remove rear U-Joint and lower drive shaft out of the way. next with a snug fitting socket remove the large nut , (pinion nut) that was hidden by the u-joint. then with a hammer knock the pinion yoke off remove bearing. replace with new bearing NOTE: check yoke for wear, you may need to use a speedy sleeve to repair damage. if it looks good you won't. replace yoke replace washer and pinion nut, (always use a new pinion nut) tighten to specified torque replace drive shaft and U-JOINT, (now is a good time to put new u-joint in while you have it apart) finished


84 gmc vandura how to replace rear axle pinion bearing?

To replace the rear axle pinion bearing on an '84 GMC Vandura, first, safely lift and support the vehicle, then remove the driveshaft and any rear axle cover. Next, remove the pinion nut and yoke to access the pinion gear. Carefully pull out the pinion assembly, replace the old bearing with a new one, and reassemble by reversing the steps, ensuring proper torque on the pinion nut and checking the bearing preload. Always consult a repair manual for specific torque specifications and procedures.


How do you remove Differential Pinion on1997 Chevy g 20?

Remove driveshaft, remove pinion nut, remove rear cover, remove axles, remove differential. Push pinion out through housing.


How do you change the pinion gears in a gm suburban?

To change the pinion gear in a differential you must first open the differential, drain the gear oil and inspect the gears and bearings. Pinion gears and ring gears are usually done as a matched set so you should plan on replacing both. Remove the axle shafts and then mark the carrier bearing caps so they can be replaced in exactly the same location and direction that they came off. remove the caps and then pull the carrier out. Measure the pinion to axle centerline distance so that you can get the new pinion in the same spot. Remove the yoke retainer nut and the driveshaft yoke and then remove the pinion from the differential housing. You should be using new bearings and races so remove the old races from the differential housing and the old bearing from the Pinion gear. The shims from the old gear should be a good starting place to set up your new pinion depth. Test fit the new pinion to see if the pinion depth is right. Install pinion bearing races, bearings and new seal. Install new ring gear and set the gear lash You may have to shim the carrier or change the pinion depth to get the right gear lash. This process usually requires expert knowledge and specialized tools and you may want to consult a qualified mechanic to do the job. There are many more detailed descriptions on the net.