answersLogoWhite

0

With a mutimeter test between each lead (usually yellow in color), the reading should be approximately one (1) ohm. or close.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

Where is the serial number on Yamaha Banshee?

The last six digits of the VIN number is the serial number on a Yamaha Banshee. The VIN number is found under the stator cover on the lower left part of the frame.


Should you advance banshee timing plus or?

Many 1000's of riders have concluded the Banshee likes +4 degrees of timing advance. That means rotating the stator plate Clockwise to make the spark happen earlier.


How do you test a motorcycle stator?

To test a motorcycle stator, first, disconnect it from the motorcycle's electrical system. Use a multimeter to check the resistance between the stator's terminals; it should match the manufacturer's specifications. Next, test for shorts by measuring the resistance between each terminal and the stator's ground; there should be no continuity. Finally, perform a voltage output test by starting the engine and measuring AC voltage at the stator terminals; it should produce voltage within the specified range when revved.


How do you test a stator on a skidoo?

To test a stator on a Ski-Doo, first, disconnect the electrical connectors and use a multimeter to measure the resistance between the stator's windings. Check for continuity between the windings and ensure there's no short to ground by measuring resistance from the windings to the stator case. Additionally, you can test the output voltage by starting the engine and measuring the AC voltage at the stator's output wires, comparing it to the manufacturer’s specifications. If the readings are outside the specified range, the stator may need replacement.


How do you test an outboard motor stator?

To test an outboard motor stator, first disconnect the stator from the wiring harness and use a multimeter to check the resistance between the stator's output terminals; refer to the manufacturer's specifications for the correct resistance values. Next, inspect for any signs of physical damage or corrosion. Additionally, test for continuity between the stator coils and the ground to ensure there are no short circuits. If any readings are outside the specified range or if there is continuity to ground, the stator may need to be replaced.


Hello Suzuki DS80 no spark what could be the problem?

check coils stator and all connections test procedure check coils stator and all connections test procedure


Can you test stator by removing battery cables?

nope....stator as in the alt? dont do it. this was a test before the computer days... you will surge/ zap the comp. or did you mean starter? either way the answer is no


How can you test a stator on a 1983 xr80 dirt bike?

yes for continuity


How do you test a Polaris stator?

To test a Polaris stator, first disconnect the stator from the wiring harness and use a multimeter set to the ohms setting. Measure the resistance between the stator's terminals according to the specifications in the service manual; typically, you should see a specific resistance range depending on the model. Next, check for any shorts to ground by testing each terminal to the stator housing; there should be no continuity. If the readings are outside the specified ranges or if there’s continuity to ground, the stator may be faulty and should be replaced.


How do you test a stator on 94 wideglide harley Davidson?

To test the stator on a 1994 Harley Davidson Wide Glide, first, disconnect the battery and remove the stator cover. Use a multimeter to measure the resistance between the stator's three yellow wires; it should typically read between 0.1 to 0.5 ohms. Next, check for continuity to ground by measuring resistance between any yellow wire and the stator case; there should be no continuity. If the readings are outside these ranges, the stator may be faulty and should be replaced.


How do you test a piaggio typhoon 50 scooter stator?

To test a Piaggio Typhoon 50 scooter stator, first, ensure the scooter is turned off and the battery is disconnected. Use a multimeter to measure the resistance of the stator's coils by checking the ohm readings between the various terminals; refer to the service manual for the specific values. Additionally, check for any shorts by testing the coils against the stator's ground. If the readings are outside the specified range or show continuity where there shouldn't be, the stator may need to be replaced.


What are the release dates for Casper - 1996 Scream Test Ms- Banshee's Kid Songs The Doctor Is Out 4-4?

Casper - 1996 Scream Test Ms- Banshee's Kid Songs The Doctor Is Out 4-4 was released on: USA: 3 October 1998