answersLogoWhite

0

use of routerrip command

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

What router prompt can you use the router rip command?

On a cisco router you would go into privilege-exec mode (enable) and then into "configure terminal" mode. From there you can use the router rip command.


Which command or set of commands will stop the RIP routing process?

no router rip


Which two statements are true about the use of the debug ip rip command on a Cisco router?

The debug ip rip command displays RIP routing activity in real time. The debug ip rip command can be issued at the user EXEC configuration mode.


How do you stop rip routing updates?

To stop RIP (Routing Information Protocol) routing updates, you can use the "passive-interface" command on routers to prevent the interface from sending RIP updates. This command can be applied to specific interfaces using the router configuration mode. Additionally, you can disable RIP entirely by removing the RIP configuration from the router or using the "no router rip" command. Finally, implementing route filtering with access control lists (ACLs) can also help control the propagation of RIP updates.


Which of the following would be the correct command sequence to enable RIP on Router B for all connected networks?

RouterB(config)# router rip


Which command enables rip on a router?

A(config)# router rip A(config-router)# passive-interface S0/0 B(config)# router rip B(config-router)# network 192.168.25.48 B(config-router)# network 192.168.25.64 A(config)# router rip A(config-router)# no network 192.168.25.32 B(config)# router rip B(config-router)# passive-interface S0/0 A(config)# no router rip


Which command correctly starts routing process in cisco router?

To start the routing process on a Cisco router, you typically enter the command router [routing_protocol] in global configuration mode, where [routing_protocol] could be protocols like rip, ospf, or eigrp. For example, to start the OSPF routing process, you would use the command router ospf [process_id], where [process_id] is a unique identifier for the OSPF process. This command enables the routing protocol and allows for configuration of related settings.


Which command is used to view the RIP routing protocol settings and configuration?

you can use SHOW IP PROTOCOL you will be able to see all running protocols in your router and its details...


What command is used to stop rip routing updates from exiting out an interface but still allow the interface to receive rip route updates?

Router(config-if)#no routing


What comment are use to delete a routing protocols in cisco router?

No router eigrp <AS #> No router ospf <process ID> No router bgp <AS #> No router rip


Implementing Distance-vector routing protocol?

First you must decide what specific protocol you want to use. Then you configure it on the individual routers. Example, with Cisco routers: Router(config)#router rip Router(config-router)#network 10.0.0.0. Router(config-router)#exit Additional commands may be required for optimization. Note: I use RIP for illustration purposes, but it is usually not the best option for routing.First you must decide what specific protocol you want to use. Then you configure it on the individual routers. Example, with Cisco routers: Router(config)#router rip Router(config-router)#network 10.0.0.0. Router(config-router)#exit Additional commands may be required for optimization. Note: I use RIP for illustration purposes, but it is usually not the best option for routing.First you must decide what specific protocol you want to use. Then you configure it on the individual routers. Example, with Cisco routers: Router(config)#router rip Router(config-router)#network 10.0.0.0. Router(config-router)#exit Additional commands may be required for optimization. Note: I use RIP for illustration purposes, but it is usually not the best option for routing.First you must decide what specific protocol you want to use. Then you configure it on the individual routers. Example, with Cisco routers: Router(config)#router rip Router(config-router)#network 10.0.0.0. Router(config-router)#exit Additional commands may be required for optimization. Note: I use RIP for illustration purposes, but it is usually not the best option for routing.


Which command will display RIP activity as it occurs on a router?

"debug ip rip" is the correct answer. Use to display information on selected RIP events. This command has many keywords that allow you to specify a variety of RIP events. You can set the level of severity for the events you want displayed; specify the desired descriptive term or a corresponding number (0-7). You can set the verbosity of the messages you want displayed: low, medium, high. Example host1#debug ip rip events Use the no version to cancel the display of any information on the designated variable.