0
To check for diagnostic codes in a 1989 Acura Legend, first, locate the diagnostic connector, usually found under the dashboard near the driver's side. Use a jumper wire to connect terminals A and B of the connector. Turn the ignition to the "ON" position without starting the engine, and watch for the check engine light, which will begin to blink in a specific sequence to indicate any stored diagnostic codes. Count the blinks to interpret the codes according to the vehicle's service manual.
What else can I help you with?
Where do you check the check engine light codes on a 1988 acura legend?
To check the check engine light codes on a 1988 Acura Legend, you need to locate the diagnostic connector under the dashboard near the driver's side. Use a jumper wire to connect the two terminals marked "TEN" and "GRD." Turn the ignition key to the "ON" position without starting the engine, and the check engine light will blink to indicate the trouble codes. Count the blinks to decipher the specific codes, which can then be referenced in a service manual for troubleshooting.
Is there a way to retrieve DTC's from a 1991 Acura Legend without using a scanner?
How do i pull codes for a 1989 acura legend
Where is the obd 1 connector for my1995 acura legend and what scanner can you use all do not read acura and Honda?
The OBD-I connector for a 1995 Acura Legend is located under the dashboard, near the driver's side, typically near the steering column. You won't find a standard OBD-II connector; instead, you'll need an OBD-I scanner specifically designed for Honda and Acura vehicles. A common scanner for this purpose is the Honda/Acura PGM-FI scanner, which can read and clear diagnostic trouble codes for OBD-I systems.
What is the diagnostic codes for a 1998 dodge ram 1500?
There are literally hundreds of diagnostic codes that would cause the check engine light to come on. Many auto parts stores will check the codes for free and tell you what is needed to fix it.
How do you check Diagnostic codes for 2008 ford focus?
Go to AutoZone. They do it for free.
How do you read the computer codes on a 1993 Acura Legend?
Follow this article: http://www.acura-legend.com/vbulletin/f13/ecu-codes-what-they-mean-g1-g2-1972/
How do you read diagnostic troble codes 1989 Honda civic?
U check the codez
How do you get codes for 1998 Acura rl?
To retrieve the radio or keyless entry codes for a 1998 Acura RL, you can check the owner's manual, as the codes are often printed on a card or included in the manual itself. If you can't find them, you can visit an Acura dealership; they may provide the codes by verifying your ownership of the vehicle. Additionally, contacting Acura customer service with your Vehicle Identification Number (VIN) may help you obtain the necessary codes.
How do you clear codes after installing a crank sensor on 96 acura 3.2?
To clear codes after installing a crank sensor on a 1996 Acura 3.2, you can use an OBD-II scanner to read and clear the diagnostic trouble codes (DTCs). Simply connect the scanner to the vehicle's OBD-II port, follow the prompts to access the trouble codes, and select the option to clear them. Alternatively, you can disconnect the vehicle's battery for about 10-15 minutes, then reconnect it, which will also reset the codes. Be sure to check that the new crank sensor is functioning correctly before clearing the codes.
What is diagnostic code for dodge neon?
Diagnostic codes are generated by your on-board computer. They tell you what problems the computer has identified with your engine. The codes are numbers. The code numbers are read by an instrument that plugs into a special jack under the dash. Auto parts stores often will check your diagnostic codes for free, or you can have your dealer do it.
How are check engine diagnostic codes read?
First you remove the cover from the diagnostic port under the driver's side of the dashboard. Then you plug the datalink cable from your scan tool into the diagnostic port. The scan tool will then show the diagnostic codes. Write them down and read a manual to see what has gone wrong.
Where is the diagnostic plug for 1996 Acura Integra?
The diagnostic plug for a 1996 Acura Integra is located under the driver's side dashboard, near the steering column. It is typically found above the accelerator pedal, and you may need to remove a cover or panel to access it. This OBD-I connector is used for connecting a diagnostic scanner to retrieve trouble codes from the vehicle's onboard computer system.
