0
Remove the front wheel behind the headlight.
Remove the screws holding the fender liner in place, just behind and around the marker light.
Carefully, pull the liner away to expose what you'll need next.
You will now see two 10mm nuts that hold the outside of the headlamp assembly in place; remove those and the one at the front grille along with the Phillip's plastic bolt in the little grille and pull the assembly out.
Second Answerer says: That wouldn't work for a 2002 model!
First, disconnect the battery.
For each bulb, there is a twist off plastic cover located directly behind the burned out bulb, that you will need to remove.
The drivers side is easy enough to access without having to remove anything.
The passenger side is a bit different.
To access the passenger side headlight cover for removal, you will need to disconnect the windshield wiper fluid reservoir, but only the top screw that you can see next to the reservoir cap.
Once this little screw is removed, you can gently push the top of the reservoir towards the driver side of the car, exposing the back of the passenger side headlight, and allowing you to easily remove the twist off cover.
They only need to be twisted about an inch or 2, and then they pop right off.
At this point, take a good look at the spring that holds the bulb in.
Squeeze the two little spring handles that are holding the bulb in, and allow it to swing out of the way, making sure you pay close attention to how the spring fits around the bulb, and the position of the electrical connection.
The connection to the bulb must be placed back in, exactly as it was before, or the spring will not latch.
Carefully remove the bulb from the headlight assembly, and unplug it from the electrical connection (twist and pull out).
Quickly examine the bulb to make sure its not broken, with sharp edges that can cut you.
BEFORE INSTALLING THE NEW BULB: Practice learning how the bulb seats into the socket and spring using the old bulb.
Once you are satisfied that you know how the bulb goes in, go ahead and put in the new bulb, and snap the two handles of the spring back in the latch position.
Once the bulb is in, reinstall the twist on cover.
These covers are round with a large tab that sticks out to help you twist them off and on.
The large tab needs to be positioned at the bottom. Push the cover in and turn clockwise an inch or two, and it should be nice and snug.
Now move the washer fluid reservoir back into position, and secure it back down with the little screw you removed earlier.
The hard part is done.
Now simply remove the screw on cover from the drivers side, and repeat the installation of the new bulb.
When that is finished, reconnect the battery making sure the cables are fastened securely to the posts, red cable on + (POSITIVE) and black cable on - (NEG).
What else can I help you with?
How do you change headlight bulb in Lexus rx300?
you can go to a auto shop and buy a rx300 bulb and after you can get someone to remove the headlight and you can remove the bulb and put the new one.
How do you adjust the headlights on a 1999 Lexus RX300?
adjust headlight
How do you remove the glove compartment for a rx300?
how do you remove the glovebox in an rx300 lexus 2002
How do you replace headlights in 2002 Lexus Rx300?
To replace the headlights in a 2002 Lexus RX300, first, open the hood and locate the headlight assembly. Disconnect the power connector from the back of the headlight bulb and remove the rubber cover. Twist the bulb socket counterclockwise to release it, then pull out the old bulb and insert the new one, making sure not to touch the glass. Finally, reassemble by reversing the steps and test the new headlight.
How do you replace parking lights for a Lexus RX300?
To replace the parking lights on a Lexus RX300, first, open the hood and locate the headlight assembly. Carefully remove the plastic cover or clips securing the assembly. Once exposed, twist the socket counterclockwise to remove it, then replace the old bulb with a new one, making sure to handle it with gloves to avoid oil transfer. Finally, reassemble the headlight assembly and test the lights to ensure they are functioning correctly.
How do you remove headlight assembly?
How to remove headlight assembly on 2003 Lexus GX470
How do you change the low beam on 2003 rx300 Lexus?
To change the low beam on a 2003 Lexus RX300, first, open the hood and locate the headlight assembly. Remove the cover or cap on the back of the assembly, then disconnect the electrical connector from the bulb. Twist the old bulb counterclockwise to remove it, then insert the new bulb by twisting it clockwise. Finally, reconnect the electrical connector and replace the cover.
How do you remove the ignition cylinder on a 2000 Lexus RX300?
To remove the ignition cylinder on a 2000 Lexus RX300, first remove the vanity engine cover by unscrewing it. Disconnect the wiring connector by pushing the clip that holds it in place. Finally, remove the bolts that hold the ignition cylinder.
How do you change the spark plugs in 2001 Lexus rx300?
How do you change the spark plugs in 2001 lexus rx300?
How much does a tune up cost for 2000 Lexus RX300?
Tune up for 1999 rx300 Lexus
How do you remove the Lexus RX300 rear bumper step pad?
pry it off with a rusty butter knife
How much to replace timing belt on a 2002 Lexus rx300?
Lexus manufacturer recommend replace timing belt on Lexus rx300 every 105,000 miles.
