0
Hi, I made a pulley locking tool by welding high tensile bolts to create a tool which fitted the two holes (which were designed to take a tool) then fitted a piece of pipe to it to reach the ground as a barrier, then undid the bolt, it was tight but after that it was simple to refit the new pulley. My old pulley delaminated before I had reached 98,000 kms. Hope this helps. ( I have an image of this tool but can't work out how to insert it here)
What else can I help you with?
Where is the crankshaft sensor located on a 2000 Hyundai Sonata v6?
On a 2000 Hyundai Sonata V6, the crankshaft position sensor is typically located near the bottom of the engine, on the engine block, close to the crankshaft pulley. It's usually mounted on the transmission bell housing or the engine block itself, making it accessible from underneath the vehicle. To locate it precisely, you may need to remove any obstructions like the engine cover or other components in the vicinity.
Where is the crankshaft position sensor located on 2001 Hyundai Sonata?
On a 2001 Hyundai Sonata, the crankshaft position sensor is typically located near the crankshaft pulley, on the engine block. It is positioned on the lower side of the engine, often toward the front or rear, depending on the specific engine type. To access it, you may need to remove some components like the engine cover or accessories around the area. Always consult the vehicle's service manual for precise location and removal instructions.
How do you remove front struts on a 2002 Hyundai sonata?
how do you remove the rear struts/shocks on 2002 hyundai sonata.
How do you remove engine mounts on 1995 Hyundai sonata?
how do you remouve engine mounts on 1995 Hyundai sonata
How do you replace water pump on 1990 Hyundai Sonata 2.4l?
you have to remove the belts and water pump pulley the water pump is located behind the timing cover.
What tools do you need to remove the crankshaft pulley pn 1995 Honda Passport?
What tools do you need to remove the crankshaft pulley on a 1995 Honda Passport?
How do you change the crank sensor on 2003 Hyundai Sonata 2.0 DOHC 16 valve?
To change the crankshaft position sensor on a 2003 Hyundai Sonata 2.0 DOHC 16 valve, first disconnect the negative battery terminal to ensure safety. Locate the sensor, which is typically found near the crankshaft pulley or on the engine block, and disconnect the electrical connector. Remove the mounting bolt(s) securing the sensor, then pull it out. Install the new sensor by reversing the steps, ensuring the connector is securely attached before reconnecting the battery.
How do remove a 1996 Chrysler damper pulley?
Depending on engine displacement in general remove belt-s then bolt holding pulley to the crankshaft then using a puller remove the pulley, when installing use a installer not a hammer to put the pulley on the crankshaft.
How do you repair a crankshaft pulley for a 98 Saturn SC2 DOHC?
u need to buy new pulley then, remove serpentine belt from engine remove bolts that hold pulley to crankshaft remove pully instalation is exact opposite of removalAnsweru need to buy new pulley then, remove serpentine belt from engine remove bolts that hold pulley to crankshaft remove pully instalation is exact opposite of removal Answeru need to buy new pulley then, remove serpentine belt from engine remove bolts that hold pulley to crankshaft remove pully instalation is exact opposite of removal
Remove the back seat of Hyundai Sonata?
2000 sonata rear seat removal
How do you remove a crankshaft pulley on a 67 Chevelle?
The crankshaft pulley unbolts from the harmonic balancer. The harmonic balancer can be removed from the crankshaft with a 3 bolt puller.
How do you remove a Hyundai Sonata fender?
ask your local hyundai dealer of coures. or mabee ...
