0
its real easy. The only thing is that the bolts are normally rusty which will make it a bit hard to take off. But first u just start at the mid-pipe(the middle of the car) you will see nuts and bolts that you can take off. Just unscrew them. You will see nuts and bolts throughout the exhaust that you unscrew off. Then take ur stock exhaust off and put on the new exhaust while replacing the bolts. Its that easy.
What else can I help you with?
Does an exhaust from a 1988 crx fit on a 87 crx?
The 1988 Honda CRX was a new generation of the model. The exhaust from a 1988 will not fit on a 1987 model.
How do you replace oxygen sensor on 1988 Honda CRX?
To replace the oxygen sensor on a 1988 Honda CRX, first, locate the sensor, which is usually found on the exhaust manifold. Disconnect the negative battery terminal, then unplug the old oxygen sensor's electrical connector. Use a wrench or oxygen sensor socket to unscrew the old sensor, and then install the new sensor by threading it into the exhaust manifold and tightening it securely. Reconnect the electrical connector and the negative battery terminal before starting the engine to test the installation.
Will an aftermarket header for a 88 crx fit on an 86 crx?
An aftermarket header for a 1988 CRX may not fit a 1986 CRX due to differences in engine configuration and exhaust design between the two model years. The 1988 CRX typically has a different engine and exhaust manifold setup compared to the 1986 model. Therefore, it's essential to verify compatibility by checking part specifications or consulting with a specialist before attempting to install an aftermarket header from one model year onto another.
Where is the fuel pump on a 1988 Honda CRX?
The fuel pump is located inside the gas tank. You have drop the tank to replace it.
How do you replace the alternator on a 1988 Honda CRX?
To remove the alternator on 1988 Honda CRX the negative battery must first be disconnected. The belt needs to be loosen and the mounting bolts need to be removed as well. When unmounted the alternator will slide off, and a new unit can be replaced.
Is there a way to make tail lights from a 1988-1991 CRX fit a 1987 CRX si?
88-91 Crx parts will not fit on a 86 crx. The 86 Crx has wider lights.
How do you replace an alternator drive belt in a 1988 Honda CRX Si?
There is a video on youtube. Just enter the question into the youtube search and you should find it.
Will a b16 fit both crx and 1988 integra?
Yes, a B16 engine can fit both the Honda CRX and the 1988 Acura Integra, as they share similar engine bay dimensions and mounting points. However, some modifications may be necessary for proper fitment, such as motor mounts, wiring harnesses, and possibly changes to the exhaust system. It's advisable to check compatibility with specific models and configurations, as variations in trim and drivetrain can affect the swap process.
Will a 1990 crx bumper fit a 1988 CRX?
yes its the same bumper alignment, all the parts from 1988-1991 are second Gen Parts for the CRX there for all the parts from those years fit each other.
Will at 1988 crx si hood fit a 1987 crx si?
No, the 1988 was a brand new design and none of the body panels carried over from 1987.
Will a exhaust from a 1990 crx fit on an 86 crx si?
A 1990 Honda CRX exhaust may not fit directly onto an 1986 CRX Si due to differences in exhaust design, mounting points, and engine specifications between the two model years. While both vehicles share similar chassis dimensions, modifications may be needed for proper fitment. It's advisable to check compatibility with exhaust components and consider using adapters or custom fabrication if necessary. Always consult with a knowledgeable mechanic or exhaust specialist for the best results.
How do you replace a water pump on a 1988 Honda CRX?
To replace the water pump on a 1988 Honda CRX, first, disconnect the negative battery terminal and drain the coolant. Remove the timing belt cover, then the timing belt by loosening the tensioner. Take out the old water pump bolts, replace the pump with a new one, and ensure the gasket is properly seated. Reassemble the timing belt, cover, and refill the coolant before reconnecting the battery.
