0
They are pretty easy. I just did my friends front rotors and pads on an 01' Acura TL's. Pull all wheels off. Take pads off shoud be a 14mm to take the calipers off. Compress the calipers. Hang up your calipers w/ wire or string so they are not hanging by the brake line. Next look on the back side of the carrier. There will be 2 17mm bolts holding a the bracket for the calipers and pads. If you have trouble breaking them free, use a brass or dead blow hammer on the wrench. (You will be doing the same to tighten the bolts back up.) Next there will be 2 Phillips head screws on the rotors. Now these can be a royal pain to get out w/ out stripping the head of the scews. I used an impact tool w/ a hammer to get them out. The craftsman one runs about 30 bucks. (It is not an air tool. It just looks like an oversized screw driver. It is spring loaded, so when you nail it w/ the hammer you will want to twist at the same time and it will break the screws loose.) Once those screws are out pull the rotors off. Degrease the new ones and reverse the process. Make sure you use the impact tool to put the screws back in. Hopefully the rotors come w/ them.
If you change your rotors I suggest changing the pads also.
This was for the fronts on an 01 Acura TL. I do not know if there is a difference between the years. Pay close attention when you start to pull the rotor off. Should be the same process for the rear I do not know. The only thing that might be different on the rear is that the bearing is in the rotor. Check the back rotors to see what they are. (If bearings are in the rear rotors, buy Bendix rotors for the rear. They come w/ the bearing carriers already in the rotor so you do not have to press them in. Buy grease and rear seal for rear rotors. Pack the bearing w/ new grease, put seal in back or rotor, make sure it is flush and put the rotor back on.) I mainly work on BMW's, and VW's.
What else can I help you with?
Are the rotors on a 2000 dodge durango in the front rear or both?
Rotors on the front drums on the rear.
Cost to replace pads and rotors on 2000 Olds alero?
I replaced my two front rotors and pads for $97.00 plus tax just last weekend.PEPBOYS
Why does your 2000 infiniti Q45 steering and console shifter shimmy when lightly applying the brakes?
resurface/replace front rotors. probably do the rear rotors too
How do you replace the front wheel bearings on a 2001 Chevy S-10 ZR2?
Did you ever get anywhere on this thread? I'm looking to replace the front bearings and rotors on my 2000 ZR2.
How to replace front brake rotors on a 2000 ford explorer sport 4x4?
How to Install Front Brake Pads Check Related links below.
What tools are required to replace front brake pad and rotors on 2000 Jeep Grand Laredo?
The tools required to replace a front brake pad and rotors on a 2000 Jeep Grand are lug wrenches, a jack, jack stands, and a C-clamp. You also will need a wrench and a turkey baster for drawing out old brake fluid.
Does a 2000 LS Saturn have drums or rotors?
Yes. Rotors on front brakes, drums on rear.
How do you replace brake rotors on 2000 SSEi?
take it to a shop
How do you change the front rotors and brakes on a 2000 olds intrigue?
Remove the wheel, the calipers and the rotors, reverse procedure with new rotors.
How do you change a front signal light on a 98 Acura RL?
How do you change front signal bulb on 2000 acura RL
What causes 2000 silverado to shake when braking?
Brake rotor/rotors are out of round / warped. Check rotors and REPLACE as needed.
How much money to replace brakes on 2000 Mercedes clk 320?
It's hard to give you a straight answer for this question. What I can tell you is it all depends on the condition of your Brakes. It can cost you any where from $600+ up to $1300. I got mine done and it cost me $700, these are the repair that was done: replace front rotors, sensors, calipers, and brake pads( front only) and the rear replace pads, caliper and re-surface the rotors. (2000 clk 320) hope this gives you an idea on it cost for a brake job.
