0
Hi All
I have just replaced the electric window mechanism in the RR door of a 1998 Daewoo Nubira.
You will need 1 x Phillips head screw driver -preferable with a small diameter shaft
Remove the 4 plastic screws from the door panel
Remove the plastic fitting on the door handle-Attention is required here as damage can occur quite easily. There are 3 plastic clips that hold the door handle surround use a small flat blade screwdriver to gently loosen clips located centre of fitting towards the rear of vehicle and top and bottom about 5 cm in from the leading edge, Now remove the electric window switch with Phillips head screwdriver ,slide switch towards the rear of vehicle to remove, Un-plug switch cable. Now you can remove the door panel ,lift panel upwards from the rear. Now you will need to remove the 2 Phillips head screws that hold the door arm support bracket once removed you can gently remove the protective plastic you will see there are 7 x 10 mm nuts that hold the assembly on remove all of these nuts next step is to remove the 2 x Phillips head screws that hold the glass onto the electric window mechanism, I did this by drilling to 6 mm holes in the door panel as close to where the screws are located (as I could NOT lower the glass) and removed screws -use a large flat blade screwdriver to pry window assembly inside the door between door and mechanism at the top 2 nuts, it can now be removed by gently prying downwards -Good Luck Hope This Helps
What else can I help you with?
How do you manually wind up a window on a electric window for a daewoo nubira?
To manually wind up the window on a Daewoo Nubira with electric windows, you'll need to remove the door panel to access the window regulator. Once you have access, locate the manual override on the window regulator, which may involve using a wrench or a screwdriver to engage the mechanism. Carefully turn the regulator to raise the window. Ensure that you reassemble the door panel securely afterward.
How do you replace window regulator 2000 ford escort ZX2?
HOW DO I REPLACE WINDOW REGULATOR MOTOR ON PASSENGER SIDE WINDOW
How do you replace a window motor and regulator on a Ford E150?
how do I replace the passenger side window regulator on an E250, 2006. the window will not release to push to top of window frame only half way?
Can you tell me what a window regulator is?
Window regulator controls the up and down motions of your car window. Both electric and manual windows have a window regulator. Not the easiest part to replace, but once you dissembled the door panel it should be fairly simple to replace.
How do I stop a window from sliding down on Intrigue?
replace the window regulator.
How do you replace a rear window regulator on 2005 CTS Cadillac?
To replace a rear window regulator on 2005 CTS Cadillac remove the side protection panel of the car door then adjust the regulator.
How do you replace a 2001 Ford Focus window regulator?
To replace a 2001 Ford Focus window regulator, first, remove the door panel by unscrewing and unclipping it to access the regulator. Disconnect the window from the regulator, then unbolt the old regulator from the door. Install the new regulator in reverse order, reconnect the window, and reassemble the door panel. Finally, test the window operation before securing everything in place.
How do you replace window regulator or window clips on rear window of 2000 grand am?
It is easy to replace the window regulator or window clips on the rear window of a 2000 Grand Am. The clips simply snap right onto the rails inside that door that connect to the window.
Should you replace both window motor and regulator?
No
How to Replace window motor in a 1999 suburban?
How to remove the window motor from the regulator
How do you fix a jeep window that has fallen down?
Replace defective window regulator
How do you replace achieva power window motor?
Remove the window regulator assembly from the door.Remove the motor from the regulator by drilling out the attaching rivets with a 3/16 in. drill bit.Connect the window motor to the regulator with 3/16 in. rivets.Install the window regulator assembly.
