0
Kia shares engineering designs with several mfg. Because of this, they do not publish drive trace info. Us ethe following options when setting Kia readiness: Early models (use Mazda drive trace): Pre-reqs: -clear codes, fuel fill between 15 and 85 %, all accessories off, cold start (prefer 8 hour cold soak engine between 68 and 86 deg. F) -start vehicle and idle for 5 min -rev engine in neutral or park to 2300-2700 rpm for 15 sec -rev engine in neutral or park to 3800-4200 rpm for 15 sec -idle engine for 20 sec with cooling fan stopped -accelerate to 52-55 mph, maintain speed in high gear for 1 1/2 min -deccelerate to 15 mph, drive for 13 min at speeds ranging from 15-35 mph -maintain a steady 25 mph for 5o sec Late models: use Hyundai drive trace -cold start (undefined by mfg), fuel fill between 15 and 85%, codes cleared, elevation below 8,000 ft -Note start time. you will need it later. Drive 2 min at 35 mph -stop and idle car 1 min -drive at 45 mph for 10 min, keeping rpms between 2000-2400 -deccelerate to 35 mph. selecting second gear, accelerate engine to 4000 rpm, and lift off throttle for 10 sec -repeat last step four more times -drive at 55 mph until 16 min have passed since starting drive trace. If time since start exceeds 20 min, evaporative monitor will not run. -Stop and idle car 4 mintip in throttle every min to change idle state. There is a universal drive cycle that requires checking car repeatedly with obd II readiness tool, so you may want to leave that to your mechanic.
What else can I help you with?
How do you reset the obdii drive cycle on 2003 Mercedes Benz e500?
How do you reset a e500 mercedes benz drive cycle
How do you reset the drive cycle on the OBDII computer on a Honda element?
To reset the drive cycle on the OBDII computer of a Honda Element, you can disconnect the negative battery terminal for about 15-30 minutes, then reconnect it. This will clear the stored diagnostic trouble codes and reset the computer. After reconnecting, you should drive the vehicle through a series of conditions to allow the OBDII system to complete its readiness tests. Make sure to follow the specific drive cycle procedure outlined in the vehicle's service manual for best results.
How do you reset the OBDII drive cycle for a 2000 Daewoo Leganza?
To reset the OBDII drive cycle for a 2000 Daewoo Leganza, you typically need to disconnect the vehicle’s battery for about 15 minutes. This will clear any stored trouble codes and reset the engine control module. After reconnecting the battery, drive the vehicle under varied conditions—accelerating, decelerating, and idling—to complete the drive cycle and allow the OBDII system to recheck emissions readiness. Always refer to the specific vehicle manual for detailed instructions.
How do you reset the drive cycle on the OBDII computer on a Toyota Highlander?
Disconnect both cables on battery, hold horn down for abouta minute, reconnect battery about 15 minutes later
What is the drive time for a '98 Chevy Cavalier after the OBDII is reset?
depends on your driving 2 days to a week. there is a procedure to do its too long to write on here Look under OBDII.com code po404 and there is a link to a drive cycle site that will tell you
How do you reset the drive cycle on the obdii Honda crv 2002?
To reset the drive cycle on a 2002 Honda CR-V, you typically need to clear the vehicle's diagnostic trouble codes (DTCs) using an OBD-II scanner. After clearing the codes, the drive cycle can be completed by following a specific sequence of driving conditions, which usually includes a mix of idling, acceleration, and steady-speed driving. This allows the onboard systems to recheck and recalibrate various sensors. Make sure to drive the vehicle under varied conditions to ensure all readiness monitors are reset.
What is the drive cycle to reset 2001 Toyota solara?
what is the drive cycle of Toyota solara 2002
Do you have to operate the sienna after battery replacement to reset the computer?
to reset the old codes you must drive it for atleast an entire drive cycle
How do you reset freeze frame data in automotive?
Two ways: the reset button on an OBDII scanner, or disconnect the battery for a couple of minutes. All this does is reset the memory, it will not "fix" a fault. If you are doing this for an emissions test, the test center will fail you if the car hasn't completed its drive cycle tests even if the "check engine" or malfunction indicator lamp isn't illuminated.
What is the Drive cycle 2003 olds alero to reset sensors?
Dan T
How do you reset the drive cycle on the computer of a Honda element?
You take out the battery and reinsert it.
How do you reset Kia Spectra 2006 keyless entry?
Need to reset alarm on my 07 Kia Spectra because I just changed the battery.
