answersLogoWhite

0

For a 2007 Honda CR-V, it's generally recommended to change the engine coolant every 60,000 miles or every 5 years, whichever comes first. However, you should also check the owner's manual for specific recommendations and any potential updates. Regular inspections for leaks or discoloration can help determine if a change is needed sooner. Always ensure to use the appropriate coolant type specified for your vehicle.

User Avatar

AnswerBot

2w ago

What else can I help you with?

Related Questions

When should you change engine coolant in a Honda civic?

At least every 50,000 mi. I would flush it at the same time.


What does service B5 mean on Honda Accord?

B = Change engine oil and filter.5 = Change engine coolant.


Do you have to change coolant on a 2005 Honda rancher 400 ATV?

Yes, you should change the coolant on a 2005 Honda Rancher 400 ATV. Regular maintenance, including coolant changes, is essential to ensure optimal engine performance and prevent overheating. It's generally recommended to replace the coolant every couple of years, or as specified in the owner's manual, to maintain the cooling system's efficiency. Always use the recommended type of coolant for your ATV.


When should you change the coolant in a Honda Civic?

You should change the coolant in a Honda Civic roughly every 60,000 to 100,000 miles, or every 4 to 5 years, depending on the type of coolant used. It's also advisable to check the owner's manual for specific recommendations related to your model year. Additionally, if you notice signs of overheating or coolant contamination, it's best to change it sooner. Regular maintenance helps prevent engine overheating and prolongs the life of your vehicle's cooling system.


Where is the coolant drain plug on the engine block of a 2003 Honda Accord ex?

where is the coolant drain plug on the engine block of Honda ACCORD 2.4 2006


How do you replace the engine coolant on a 1991 Honda Civic?

The engine coolant on a 1991 Honda Civic is replaced by turning the drain petcock and releasing the coolant. The filler cap is then removed and coolant added until the system is full again.


How do you change the coolant in a 2004 Honda 500 rubicon?

To change the coolant in a 2004 Honda 500 Rubicon, first ensure the engine is cool and then locate the radiator drain plug at the bottom of the radiator. Remove the drain plug and allow the old coolant to fully drain into a suitable container. Once drained, close the plug and refill the radiator with a 50/50 mixture of Honda-approved coolant and distilled water. Finally, run the engine for a few minutes to circulate the new coolant, checking for leaks and topping off as necessary.


How do you change the coolant ina a Honda helix motor scooter?

To change the coolant in a Honda Helix motor scooter, first ensure the engine is cool and then locate the coolant reservoir and radiator. Open the radiator cap and drain the old coolant by removing the drain plug at the bottom of the radiator. Once drained, close the drain plug, refill the radiator with the appropriate type of coolant, and replace the radiator cap. Finally, run the engine for a few minutes to circulate the new coolant and check for leaks.


How can you check the Engine Coolant Temperature sensor on my 91 Honda Prelude SI 2.1L?

How can I check the ENGINE COOLANT TEMPERATURE (ECT) sensor on my 1991 HONDA PRELUDE SI 2.1L


What does service due B25 mean for Honda odyssey 2006?

B. Change engine oil & filter. 2. Change engine air filter & cabin filter. Check all belts. 5. Replace engine coolant.


Where is the coolant temperature sensor located in a 2006 Honda civic?

The 2006 Honda Civic coolant temperature sensor is located on the front of the engine. The coolant temperature sensor will be in the vicinity of the thermostat housing.


How do you change coolant on Honda 1800C?

To change the coolant on a Honda 1800C, start by ensuring the engine is cool and then locate the radiator drain plug, usually at the bottom of the radiator. Place a drain pan underneath, remove the plug, and let the old coolant flow out completely. Once drained, replace the drain plug, refill the radiator with fresh coolant through the filler neck, and also top off the reservoir if needed. Finally, run the engine briefly to allow the coolant to circulate, check for leaks, and ensure the coolant level is correct.