0
Why would your 2006 Mitsubishi endeavor tcl light and service engine soon light come on and the car shakes this just started?
The TCL (Traction Control Light) and Service Engine Soon light coming on in your 2006 Mitsubishi Endeavor, coupled with the car shaking, could indicate several issues. Common causes include problems with the engine such as misfires, faulty spark plugs, or issues with the fuel system. Additionally, a malfunctioning traction control system or a faulty wheel speed sensor could trigger the TCL light. It's advisable to have the vehicle diagnosed with an OBD-II scanner to pinpoint the exact issue and prevent further damage.
What else can I help you with?
How do you reset service engine soon light on a 2005 Mitsubishi Endeavor?
The owners guide for my '04 Endeavor says do not disconnect the battery I think, or the on board diagnostic record will be lost. maybe this would also clear the service engine light?
Why would the service engine soon light come on in a 2004 Mitsubishi Endeavor?
I HAVE A 2004 MITSUBISHI ENDEAVOR, AND THE ONLY TIME MY CHECK ENGINE LIGHT CAME ON IS WHEN I FAILED TO CLOSE MY GAS CAP TIGHTLY. THE LONGEST THE LIGHT STAYED ON WAS FOR 3 DAYS AND THEN IT WENT OFF.
How do I reset service engine soon light on a Mitsubishi Endeavor?
The proper course of action is to have the car serviced by an authorized garage, who will reset the service light when they're done.
Where is Mitsubishi Endeavor spark plug location?
The spark plugs on a Mitsubishi Endeavor are located on the engine cylinder head. To access them, you'll need to remove the engine cover and the ignition coils, which sit directly above the spark plugs. The Endeavor typically has a V6 engine, with the spark plugs positioned in a line along each side of the engine. Always consult the vehicle's service manual for specific details related to your model year.
Where are the sparkplugs in a 06 Mitsubishi endeavor?
In a 2006 Mitsubishi Endeavor, the spark plugs are located on the engine, accessible by removing the engine cover and the ignition coils. The Endeavor is equipped with a V6 engine, so there are six spark plugs, one for each cylinder. Each spark plug is situated on the top of the engine, connected to the ignition coil, which needs to be removed to access the plugs for replacement or inspection.
Where is the crankshaft position sensor located on 2004 Mitsubishi Endeavor?
The crankshaft position sensor on a 2004 Mitsubishi Endeavor is typically located near the bottom of the engine, on the engine block, near the crankshaft. It is often positioned at the rear of the engine, close to the transmission bell housing. You may need to access it from underneath the vehicle for easier visibility and access. Always consult the vehicle's service manual for specific details and diagrams.
Where is the valve to plug in a evap smoke tester on a Mitsubishi Endeavor?
On a Mitsubishi Endeavor, the valve to plug in an evap smoke tester is typically located in the engine bay. Look for the EVAP service port, which is usually found on or near the intake manifold or the EVAP canister. It may be covered by a cap or a rubber grommet. Always refer to the vehicle's service manual for the exact location and details specific to your model year.
Where is your power steering on a Mitsubishi endeavor?
The power steering pump is located(looking at engine from front of car) on the bottom of the engine on the left side.
How do you get the car to run after replacing the instrument cluster in your Mitsubishi endeavor?
The Engine Control Module (ECM) probably has to be flashed to relearn the new cluster. This is a job for the Mitsubishi dealer.
What causes the service engine soon light to come on on a 2004 Mitsubishi Endeavor?
The "Service Engine Soon" light on a 2004 Mitsubishi Endeavor can be triggered by various issues, including problems with the engine's emissions system, a faulty oxygen sensor, a loose or damaged gas cap, or issues with the ignition system. It may also indicate a need for routine maintenance, such as an oil change or air filter replacement. To determine the exact cause, it's best to have the vehicle scanned for diagnostic trouble codes. Addressing the underlying issue promptly can help prevent more serious engine problems.
Where is the oil filter located on a 2004 Mitsubishi endeavor?
underneath the engine passenger side, at the back of the air conditioning compressor
How do you reset service engine soon light on a 2004 mitsubishi endeavor?
To reset the "Service Engine Soon" light on a 2004 Mitsubishi Endeavor, you can use an OBD-II scanner to clear the trouble codes that triggered the light. Alternatively, you can disconnect the negative battery terminal for about 15 minutes, which will reset the vehicle's computer and turn off the light. However, if the underlying issue isn't resolved, the light will likely come back on. Always ensure any necessary repairs are made before resetting the light.
