0
A single cable carrying video will be carrying a composite video signal. This signal has brightness and two color signals encoded into a single signal. To generate a component signal (YPbPr)a video decoder is required. They are available from many sources from low cost domestic units to stunningly expensive broadcast models. The better the decoder, the better the resulting image. It is very important to understand that a composite signal has suffered losses because of the encoding. Decoding the signal to component does not restore that quality. Component interfaces can handle high definition as well as standard definition signals. Decoding a composite signal will result in a standard definition signal. Connecting it to a high definition input will not result in a high definition signal. Normally, the only reason to decode the signal to component is to interface to a device that only accepts component signals.
What else can I help you with?
Is it possible to convert YPbPr output to Coaxial output?
Not generally no. There would be no point. The easiest is to convert the standard yellow video out to coax with an RF modulator
Is s video beter than ypbpr?
I dont believe it is. YBbPr is capable of outputting High definition (1080) where as S-video is Standard Definition
Is there an rf modulator that has ypbpr ends intead of regular yellow white red?
As rf modulators are usually mains powered convention says the standard cabling is easier to get
How do you get sound from ypbpr?
To get sound from YPbPr (component) cables, you will need a separate audio connection such as analog audio cables or an audio extractor that combines the audio signal into the same cable as the video. YPbPr cables only carry video signals, so you must use a separate audio connection to transmit sound to your audio device.
Can a s video cable replace a ypbpr cable?
S-video is a two wire interface while ypbbr is a three wire interface. Therefore, an S-video cable cannot be used for any component signals. S-video supports only standard definition, that is, PAL or NTSC color encoding. Component signals (ypbbr) support both standard definition and high definition.
What type of component video is characterized by having three RCA plugs at each end?
RGB, YPbPr is characterized by having three RCA plugs at each end.
Coaxial adapter for ypbpr cable?
Coaxial adapters for YPBPR cable can be found at most Radio Shack stores. This type of cable in VGA and Audio to HDMI conversions.?æ
How can you connect a gamecube to a TV with component YPbPr and video and audio RL inputs - and will it lag?
Nintendo released a component (YPbPr) cable when the GameCube launched, but quickly stopped supporting it. Newer consoles don't have the "Digital A/V Out" port at all. If you have one of the original models with that port, you can try to track down the component video cable, although they tend to be rather expensive since there weren't many made. There are no cheaper, third-party alternatives for this cable. To when connecting the system to your TV, you will also need the original composite (yellow/red/white) cable for the RL audio, since the component cable does not have its own audio plugs. There will be no lag if the system is connected to the TV with these cables.
What is an y-pb-pr input?
YPbPr is an analog component video signal that splits the video signal into three separate components: Y for brightness (luma), Pb for the difference between blue and luma, and Pr for the difference between red and luma. This signal is commonly used for transmitting high-definition video signals.
What is the different between s video cable and ypbpr cable?
S-Video is a type of composite video signal. The 4 pins are Chrominance, Luminance, and 2 grounds. Your standard composite video cable combines Chrominance and Luminance into one signal, which is then separated again by the TV. An S-video cable removes this step. The "y, pB, pR" cable set is known as "component" video. this cable goes one step further than S-Video, breaking down the Chrominance signal to individual colors, using Red (pR), Blue (pB) and Luminance (y). The TV then uses additive and subtractive methods to determine Green.
What is the difference between Pr Pb Y and Cr Cb Y audio video ports. will my devices work if a connect the two ports together?
They are both color space video but PrPbY is analog video and CrCbY is digital video.TriviaConventionally the Y is first followed by b then r, as in YPbPr which has led to the wires being known as 'yipper' lines/cables.
Does ypbpr carry audio and video?
Y Pb Pr is a form of component video with three signals. Y is the brightness signal while Pb and Pr each carry color information. All three are required to produce a full color image and they do not carry audio. Audio will usually require a further two connectors for stereo audio.
