0
It should tell you in the user instructions or installation manual, or on a nameplate.
However, you can estimate the load by converting btu/hr into watts then dividing by the voltage you're using (e.g., 220, 110).
10,000 / 3.412.. is 2931 watts. At 220 volts it would draw 13.3 amps (or slightly more for inefficiencies in the compressor, fan, etc), while operating normally. Because this is more than 80 percent of the next-lower-rated breaker of 15A, you would install a 220-v breaker for a minimum of 16A (i.e., the next available size for your panel).
What else can I help you with?
What size circuit breaker for a 1 ton air conditioner unit?
For a 1 ton air conditioner unit, the circuit breaker size typically ranges from 15 to 20 amps. The exact size needed will depend on the specific model and requirements of the air conditioner, so it is best to consult the manufacturer's specifications or an electrician to determine the appropriate circuit breaker size for your unit.
What size amp breaker for a 220V air conditioner?
The size of the amp breaker for a 220V air conditioner will depend on the specific requirements of the air conditioner. As a general guideline, you can calculate the required amps by dividing the air conditioner's wattage by the voltage (220V). For example, if your air conditioner is rated at 5500 watts, you would need a breaker of at least 25 amps (5500 watts / 220 volts = 25 amps). It is always best to consult the manufacturer's specifications or a licensed electrician to ensure the correct size breaker is installed.
Can a 12000 BTU air conditioner run on 15 amp breaker?
It is possible for a 12000 BTU air conditioner to run on a 15 amp breaker, but it may cause the breaker to trip if there are other appliances drawing power on the same circuit. It is recommended to have a dedicated circuit for the air conditioner to prevent overloading the breaker.
How many pole breaker for air condition?
If the power requirement is 120 volts it will be connected to a single pole breaker rated at the amperage requirement of the air conditioner. If the voltage of the air conditioner is 240 volts, then a two pole breaker will be required.
What do you do when your air conditioner trips the breaker when it kicks on?
Try adding a cercuit breaker right on the AC.
Why does my air conditioner trip the breaker immediately when I turn it on?
Your air conditioner may be tripping the breaker immediately when turned on due to an electrical issue, such as a short circuit or overload. It is recommended to have a professional technician inspect and repair the air conditioner to prevent further damage.
What is the cable size for 7.5kw slit system air conditioner?
The wire is sized to the maximum overcurrent protection device (Max circuit breaker) ampacity. This is listed on the nameplate of the outdoor condensing unit. Size the wire to match the breaker.
Can an 18000 BTU air conditioner have Freon added?
Yes, call a certified technician to do the replacement of the freon.
What is the Armstrong air conditioner model number SCU10E18A-4 tonnage?
It is a 1-1/2 ton: 18000 BTU (unit size)/12,000 BTU (per ton)=1.5
What size circuit breaker for a 208 volt 3 -phase 8 ton air conditioner?
For an 8 ton air conditioner operating on 208 volts 3-phase, you would typically need a circuit breaker size of around 40-50 amps. It is recommended to consult the specific manufacturer’s guidelines for precise sizing to ensure safe and proper operation of the air conditioner.
Will a circuit breaker be the cause of an air conditioner not turning on?
It is possible if the circuit breaker has tripped or is faulty. The best way to check is by unplugging the air conditioner, and plugging in a table lamp. If the lamp lights up, then you know that the circuit breaker is working, if not then it is faulty.
Can you use a 20 amp breaker for window unit air conditioner?
A 20 amp breaker might actually be needed for the installation. It depends on the wattage and voltage of the window air conditioner.
